M103

Instrukcja serwisowa silnika M103 (Mercedes-Benz, oryginał po angielsku), odczytana ze skanów WIS. Rozdziały według grup instrukcji.

Engine removal and installation, ventilation, crankcase

  1. Engine and Model Survey
  2. Warning instructions when hood open
  3. Testing compression pressure
  4. Cranking engine with starter
  5. Testing cylinders for leaks
  6. Inspecting, assessing cylinders with inspection lamp
  7. Removing and installing engine
  8. Function description of crankcase ventilation
  9. Removing and installing cylinder head cover
  10. Notes regarding crankcase
  11. Measuring, drilling and honing cylinder bores
  12. Facing crankcase contact surface
  13. Servicing threaded holes for cylinder head boits
  14. Cleaning, sealing main oil galleries
  15. Replacing core plug in crankcase
  16. Removing and installing timing case cover
  17. Removing and installing front cover at top
  18. Replacing radial seal in front cover
  19. Removing and installing closing cover
  20. Checking for leaks at rear of engine
  21. Removing and installing oil sump (except 4MATIC)
  22. Removing and installing oil sump (4MATIC front axle housing)
  23. Notes regarding cylinder head
  24. Checking, tightening cylinder head bolts
  25. Servicing spark plug threads in cylinder head
  26. Removing and installing cylinder head
  27. Checking, facing cylinder head contact surface
  28. Widening camshaft bearing bores (repair size)
  29. Servicing threads for camshaft bearing cap bolts
  30. Pressure-testing cylinder head
  31. Cleaning, sealing oil longitudinal gallery in cylinder head

Crankshaft assembly

  1. Removing and installing crankshaft
  2. Checking, replacing and tightening conrod bolts
  3. Servicing, alining and mounting conrod in bearings
  4. Removing and installing pistons
  5. Pistons, matching and dimensions
  6. Replacing piston rings
  7. Checking and servicing crankshaft
  8. Mounting crankshaft in bearings
  9. Replacing front crankshaft radial seal
  10. Replacing rear crankshaft radial seal
  11. Removing and installing grooved ball bearing and end cover in
  12. Removing and installing belt pulley/vibration damper and hub
  13. Checking, correcting setting of TDC sensor
  14. Removing and installing flywheel! or driven plate
  15. Machining flywheel (except two-mass flywheel)
  16. Replacing ring gear
  17. Function of two-mass flywheel
  18. Removing and installing two-mass flywheel
  19. Removing and installing needle bush in two-mass flywheel
  20. Removing and installing holding lock for crankshaft/ring gear

Engine timing, valve train

  1. Checking and replacing hydraulic valve clearance compensating
  2. Checking basic position of hydraulic compensating elements
  3. Adjusting basic setting of hydraulic compensating elements
  4. Checking camshaft timing
  5. Adjusting camshaft timing
  6. Removing and installing driver on camshaft
  7. Removing and installing rocker arm bearing bracket
  8. Removing and installing camshaft
  9. Replacing threaded bush in front of camshaft
  10. Replacing end cap in rear of camshaft
  11. Checking basic position of camshaft
  12. Adjusting basic position of camshaft
  13. Removing and installing rocker arms
  14. Removing and installing valve springs
  15. Checking valve springs
  16. Replacing valve stem seals
  17. Checking valve guides
  18. Replacing valve guides
  19. Checking valves
  20. Replacing valve seat rings
  21. Machining valve seat rings
  22. Removing and installing chain tensioner
  23. Replacing timing chain
  24. Removing and installing tensioning rail
  25. Removing and installing guide rail
  26. Removing and installing crankshaft gear

Mechanical gasoline injection system CIS

  1. Additional designations for models and components
  2. Summary of models and components
  3. Vehicle features
  4. Influencing variables of mechanical/electronic mixture adaptation
  5. Function diagram KE injection
  6. Testing electrical components of the KE injection system
  7. Wiring diagrams
  8. Retrofitting second fuel pump, model 124.026/030
  9. Testing, adjusting engine
  10. Testing kickdown switch
  11. Testing engine output and exhaust emission on the roller
  12. Determining fuel consumption by driving on the road
  13. Testing fuel pressures and internal leaktightness
  14. Testing restrictor in fuel distributor for clear passage
  15. Testing starting valve actuation
  16. Performing fuel quantity comparison measurement
  17. Replacing seal for control plunger
  18. Replacing, centering air flow sensor plate and checking, adjusting
  19. Removing and installing mixture control unit with air guide
  20. Replacing fuel distributor
  21. Removing and installing fuel accumulator
  22. Replacing air flow sensor
  23. Replacing, adjusting throttle valve switch
  24. Replacing electrohydraulic actuator
  25. Removing and installing KE control unit
  26. Testing electronic idle speed control
  27. Testing, adjusting idle speed or special exhaust emissions test
  28. Performing cold start
  29. Testing starting device
  30. Testing on/off ratio as of 1986
  31. Replacing oxygen sensor
  32. Removing and installing fuel filter
  33. Testing fuel pump
  34. Removing and installing fuel pump
  35. Removing and installing fuel pump set
  36. Testing fuel pump relays (except engine 103.984 and as of
  37. Replacing non-return valve for fuel pump
  38. Replacing rubber rings or rubber stop for fuel pump set
  39. Removing and installing throttle valve body
  40. Testing injection valves
  41. Removing and installing injection valves

Air intake, air cleaner, turbocharger

  1. Removing and installing, replacing air cleaner
  2. Replacing intake air cowl

Belt drive

  1. Removing and installing poly-V-belt
  2. Checking poly-V-belt, typical damage
  3. Poly-V-belt, running diagrams, dimensions
  4. Removing and installing tensioning device
  5. Checking tensioning device
  6. Retrofitting shock absorber to tensioning device
  7. Removing and installing guide pulley

Intake and exhaust manifold, emission control

  1. Distinguishing features of vehicles with emissions control system
  2. Testing catalytic converter warning system
  3. Testing oxygen sensor failure indicator
  4. Converting USA tourist vehicles with catalytic converter
  5. Removing and installing intake manifold, replacing gasket
  6. Replacing intake manifold (intake manifold removed)
  7. Removing and installing exhaust manifold
  8. Testing air pump
  9. Removing and installing air pump
  10. Removing and installing electromagnetic clutch
  11. Removing and installing air injection/transmission shiftpoint retard
  12. Removing and installing air pump switchover valve
  13. Testing exhaust gas recirculation
  14. Removing and installing exhaust gas recirculation switchover vaive

Electrical system engine

  1. Notes regarding working on brakerless transistorized ignition
  2. Use of unleaded fuels
  3. Replacing ignition cables with M3 cable screw
  4. Testing ignition timing
  5. Adapting ignition timing point with resistance trimming plug to
  6. Replacing spark plugs
  7. Testing electronic ignition system with variable characteristics EZL
  8. Removing and installing EZL ignition control unit
  9. Removing and installing crankshaft position sensor
  10. Removing and installing engine systems control unit (N16)
  11. Removing and installing high voltage distributor

Engine lubrication

  1. Engine oil and filter change
  2. Oil circuit
  3. Testing oil pressure
  4. Testing oil pressure sensor
  5. Operation of oil pressure gauge
  6. Measuring oil consumption
  7. Operation of oil filter
  8. Removing and installing oil filter
  9. Operation of oil-to-coolant heat exchanger
  10. Removing and installing oil-to-coolant heat exchanger
  11. Removing and installing oil pump
  12. Replacing and riveting oil pump chain
  13. Removing and installing oil pressure relief valve in oil pump
  14. Removing and installing oil shield at crankshaft
  15. Operation of electrical oil level gauge
  16. Removing and installing oil level sensor
  17. Testing oil level sensor
  18. Checking dipstick and guide tube
  19. Replacing oil nozzle return lock
  20. Removing and installing camshaft oil pipe

Engine cooling

  1. Switching points in the cooling system
  2. Coolant circuit
  3. Draining, pouring in coolant – Antifreeze protection table
  4. Cleaning cooling and heating system
  5. Testing cooling system for leaks
  6. Removing and installing coolant thermostat
  7. Removing and installing coolant pump
  8. Replacing connecting pipe from cylinder head coolant pump
  9. Sealing coolant pump
  10. Retrofitting coolant pump drain pipe
  11. Removing and installing viscous fan clutch
  12. Removing and installing viscous fan clutch bearing bracket
  13. Removing and installing, adjusting fan shroud
  14. Removing and installing radiator
  15. Replacing vent connection at radiator
  16. Testing cooling system pressure cap
  17. Operation of electric coolant level gauge
  18. Removing and installing expansion tank
  19. Removing and installing overflow tank

Engine suspension

  1. Checking, stress-relieving front engine mounts
  2. Removing and installing rear engine mount
  3. Adjusting rear engine mount (freeway-hop), model 124 USA
  4. Engine bearing cooling, model 201 (retrofitting)
  5. Setting engine stop, model 124 4MATIC
  6. Removing and installing engine carrier
  7. Removing and installing front engine mounts

Throttle control

  1. Lubricating accelerator control linkage, checking ease of
  2. Removing and installing engine longitudinal accelerator control
  3. Removing, installing and adjusting chassis accelerator control
  4. Notes for test and repair work on vehicles with ASR
  5. ABS/ASR and electronic accelerator pedal initial test
  6. Adjusting accelerator control
  7. Testing electronic engine control
  8. Removing and installing electronic accelerator pedal control unit
  9. Removing and installing electronic accelerator pedal actuator
  10. Removing and installing electronic accelerator pedal position
  11. Removing and installing accelerator pedal
  12. Removing and installing fire wall bearing with accelerator pedal
  13. Removing, installing and adjusting bowden cable
  14. Testing Tempomat cruise control, vehicles with ASR

Fuel system

  1. Removing and installing fuel tank
  2. Removing and installing fuel gauge sender
  3. Removing and installing fuel expansion tank, model 107
  4. Testing fuel evaporation control system
  5. Removing and installing activated charcoal filter
  6. Removing and installing regeneration switchover valve (fuel

Exhaust system

  1. Converting vehicle with catalytic converter
  2. Replacing center, tail silencer
  3. Removing and installing closed-loop catalytic converter
  4. Retrofitting open-loop catalytic converter
  5. Removing and installing exhaust system
  6. Removing, installing, replacing and bolting exhaust system as of
  7. Replacing carrier for exhaust bracket at transmission

Modification notes

  1. Modification Notes Engine 103 Combustion! KE Injection
  2. Modification Notes Engine 103. Combustion II KE Injection
  3. Modification Notes Engine 103 Combustion III KE Injection

Program repairs

  1. Programed Repairs Engine 103 Combustion! KE Injection
  2. Programed Repairs Engine 103 Combustion KE Injection
  3. Programed repairs Engine 103 Mechanicals
  4. Programed repairs Engine 103 Mechanicals III

Technical modifications

  1. Technical Modifications Engine 103 Combustion! KE injection
  2. Technical Modifications Engine 103 Combustion III KE Injection
  3. Technical Modifications Engine 103 Combustion Injection