OM615
Instrukcja serwisowa silnika OM615 (Mercedes-Benz, oryginał po angielsku), odczytana ze skanów WIS. Rozdziały według grup instrukcji.
General, technical data
- Instructions for Use of Service Manual A
- Instructions for Use of Service Manual A (continued)
- Instructions for Use of Service Manual A (continued)
- Technical data
- Removal and installation of engine (oil quantity)
- Checking compression pressure
- Checking cylinders for leakage
- Measurement of oil consumption
- Removal and installation of front engine mounts
- Removal and installation of rear engine mount
- Removal and installation of front engine stop
- Adjustment of engine stop
- Removal and installation of engine shock absorber
- Retrofitting engine shock absorber (engines 615, 616 in type 123.1)
- Retrofitting engine shock absorber (engine model 617 in type 123.1)
- Engine ventilation — Functional description
- information for model year 1982
Crankshaft assembly
- Assessment of cylinder bores
- Measurement of cylinder bores
- Refacing crankcase parting surface
- Renewing, boring and honing cylinder liners
- Removal and insertion of steel balls for main oil galleries
- Replacement of core hole caps in crankcase
- Installation and centering of intermediate flange
- Removal and installation of oi! pan assembly
- Checking, replacement and tightening of big-end clamp bolts
- Reconditioning and squaring connecting rods
- Removal and installation of piston
- Checking and reconditioning crankshaft
- Refitting crankshaft bearings
- Replacement of front radial seal on crankshaft
- Replacement of aft radial seal on crankshaft
- Removal and installation of deep-groove ball bearing and locking ring in crankshaft
- Removal and installation of pulley, vibration damper and balance plate
- Balancing balance plate statically
- Checking and correcting adjustment of TDC transmitter adjusting slide
- Removal and installation of crankshaft sprocket
- Removal and installation of flywheel and driven plate
- Refacing flywheel
- Replacement of flywheel ring gear
- Balancing flywheel statically
- Notes on overall balancing of engine 617
Engine timing, valve train
- Repair instructions for cylinder heads and cylinder head gaskets
- Cylinder head bolts and cylinder head bolt torquing
- Retightening hexagon socket cylinder head bolts
- Removal and installation of cylinder head
- Removal and installation of precombustion chambers
- Refacing cylinder head parting surface
- Pressure-testing cylinder head
- Checking and replacing valve guides
- Refacing valve seats
- Checking and adjusting valve clearance
- Checking and adjusting camshaft timing
- Removal and installation of camshaft
- Grinding camshaft journals
- Removal and installation of rocker arms and rocker arm brackets
- Replacement of rocker arms and rocker arm brackets
- Removal and installation of valve springs
- Checking valve springs
- Replacing valve stem seals
- Checking and refacing valves
- Removel and installation of chain tensioner
- Replacement of timing chain
- Removal and installation of tension rail
- Removal and installation of slide rails
- Removal and installation of helical gear shaft
- Removal and installation of intermediate gear shaft
- Removal and installation of idler gear
Fuel injection system
- Survey engine — model — injection pump
- Operation of injection pump and rpm governor
- Adjustment of idle speed and idle speed adjuster
- Inspection and adjustment of no-load max speed
- Checking injection pump for begin of delivery (according to high pressure
- Checking injection pump for begin of delivery (according to low pressure
- 07.1115 Adjusting injection pump for begin of delivery (after checking begin of delivery)
- Checking injection pump for offset of begin of delivery (after checking begin of
- Checking pneumatic governor of injection pump for leaks (engine 615, 616)
- Adjusting governor spring of injection pump (engine 615, 616)
- Checking injection nozzles
- Disassembly, cleaning, assembly and adjustment of injection nozzles
- Venting of injection system
- Checking fuel pump and overflow valve
- Checking key starter for leaks
- Removal and installation of injection pump
- Displacing injection pump (after adjusting begin of delivery)
- Replacing pipe connection, pressure valve or copper sealing ring of injection pump
- Replacing diaphragm of injection pump, adjusting compensating path
- Replacing vacuum box on injection pump
- Replacing altitude adjusting box
- Removal and installation of injection nozzles (injectors)
- Removal and installation of fuel pump
- Removal and installation of injection timer
- Replacing fuel filter
Air intake, air cleaner, turbocharger
Belt drive
Intake and exhaust manifold, emission control
Electrical system engine
Engine lubrication
Engine cooling
- Coolant circuit and engine cooling
- Draining and filling-in of coolant — Anti-freeze table
- Cleaning the colling system
- Removal and installation of thermostat
- Removal and installation of water pump
- Reconditioning of water pump
- Sealing of water pump
- Removal and installation of water pump housing
- Viscofan coupling, temperature—controlled (engine 617)
- Removal and installation of radiator
- Reconditioning of radiator
- Checking radiator cap
- Thermostat layout
Throttle control
- Adjusting regulating linkage, vehicles with lefthand steering
- 2 Adjust vacuum control valve. For this purpose,
- Vehicles with automatic transmission
- Removal and installation of engine longitudinal regulating shaft
- Removal, installation and adjustment of front wall regulating shaft
- Removal and installation of accelerator pedal
- Adjusting start and stop cable control (engine 615, 616 with M-injection pump)