Checking injection nozzles

WIS 07.1-135

Test values

Opening pressure in bar gauge pressure’? Injection nozzles Engine of used injection Bosch designation of new injection nozzles nozzles at least

Standard version and @us) GJ)

615.913/940 DNOSD 1510

615.941 616 (48 kW) ON OSD 220 115-123 100 617 (59 kW)

616 (53 kW) 3) 617 (65 kW) ON OSD 240

C CGS starting 1979 Identification cs) only: Injection pump with lead-sealed governor housing.

615.913/940 DNOSD 1510

615 616 (48 kW) DNOSD 220 115-123 100 617 (59 kW)

616 2) 617 DN OSD 240

Gs A) starting 1979 Identification: Injection pump with green type-rating plate.

by DN 0 SD 240?) 115-123 100

1) The difference in opening pressure of injection nozzles within one engine should not amount to more than 5 bar gauge 2) Pressure. 3) Starting 1979 nozzie holder with edge-type filter. ) Engine 616, 617 starting from increased output.

Tightening torques

Injection nozzle upper and lower half

Torque wrench 1/2″ square, 000 589 22 2100

Checking injection nozzles – rysunek

Socket 27 mm, 1/2” square for injection nozzle – 001 589 65 09 00

Cleaning kit – 000 589 00 68 00

Conventional tools

e.g. made by Bosch, D-7000 Stuttgart Tester EFEP 60 H Order no. 0 681 200 502

e.g. made by Bosch, D-7000 Stuttgart Cleaning needle 0.13 mm @ Order no. KDEP 2900/3

Note Use only clean testing oil or filtered diesel fuel for testing. When testing a nozzle, never move hand into jet of a nozzie. Jet will deeply enter flesh and will destroy the tissue. Fuel entering into blood may cause blood poisoning.

Attention! The shutoff valve of pressure gauge should remain closed during jet and buzzing test, since otherwise the pressure gauge may be damaged by excessive pressure increase.

Checking injection nozzles – rysunek

The injection nozzle with Bosch designation DN O SD 240 is a perforated pintle nozzle. This nozzle differs from the pintle nozzle by a crosswise and lengthwise bore (14 and 15) in throttle pintle. In addition, a maintenance-free rod-type filter (13) is pressed into top of injection nozzle holder (7).

Nozzle needle OBINMAMH AWN Nozzle body Nozzle holder element Pressure pin Injection nozzle holder bottom Compression spring Injection nozzle holder top Leak oil connection Fuel feed 10 Steel washer 11. Ring groove and feed bores 12 Pressure chamber in nozzle body 13 Rod-type filter 14 Crosswise bore 15 Lengthwise bore

Testing

1 Remove injection nozzles (07.1—230).

2 Connect removed injection nozzle to tester. With Pressure gauge switched off, plunge down energetically several times. With a perfectly moving nozzle needle nozzle should buzz together with a high whistling sound.

Checking injection nozzles – rysunek

3 Jet test with shutoff valve closed. Insert injection nozzle into tester. At short, fast partial strokes (approx. 2 strokes per second) the jet should be rather concentrated and should break well. Individual drops, diagonal or diagonally broken jets, slightly wide jets are of no significance for combustion in engine.

A Good injection nozzle Jet concentrated and well atomized B Damaged injection nozzle Jet too wide, streaky and not concentrated

Checking injection nozzles – rysunek
Checking injection nozzles – rysunek

slow, uniform downward movement of hand lever (approx. 4–6 seconds per stroke) a distinct, vertical cord-like jet (arrow) should come out of longitudinal bore (15). If no cord-like jet comes out, check longitudinal bore with cleaning needle 0.13 mm dia for unobstructed passage. If the longitudinal bore is clear, the injection nozzle can be used again.

Note: Test procedure also applies to new injection nozzles.

14 Crosswise bore 15 Lengthwise bore

5 Buzzing test. Push hand lever slowly fully down (approx. 1 stroke per second); a damped buzzing of injection nozzle should be heard.

If the jet or the buzzing test are not in order, flush injection nozzle by means of several short, fast full strokes (2 strokes per second). The jet should be concentrated and emerge with a clearly heard, high whistling sound. Replace injection nozzle if required.

Checking injection nozzles – rysunek

6 Test opening pressure of injection nozzle.

Slowly push hand lever down (1 stroke per second) with shutoff valve open. When ejection begins, read ejection pressure; injection nozzle should buzz distinctively. Set injection nozzle to specified ejection pressure (opening pressure), if required (07.1–137).

7 Check injection nozzle for leaks.

With shutoff valve open, slowly push pump lever down up to ejection pressure. Release pump lever, ejection pressure should remain constant. In the event of leaks, disassemble injection nozzle, clean, assemble and adjust (07.1–137).