M117 5,6

Instrukcja serwisowa silnika M117 5,6 (Mercedes-Benz, oryginał po angielsku), odczytana ze skanów WIS. Rozdziały według grup instrukcji.

General, technical data

  1. Instructions for use of service manual 00
  2. Engine and vehicle identification 00
  3. Vehicle identification number locations
  4. Technical data

Engine removal and installation, ventilation, crankcase

  1. Technical data (continued)
  2. Checking compression pressure
  3. Checking cylinders for leaks
  4. Evaluating cylinder bores
  5. Removal and installation of engine (oil capacity)
  6. Engine breathing system — operation
  7. Measuring, honing and silicon—lapping cylinder bores
  8. Measuring, honing and silicon—lapping cylinder bores (continued)
  9. Reconditioning of threaded bores for cylinder head bolts
  10. Reconditioning threaded bores for intermediate flange and transmission mounting
  11. Coolant preheater in crankcase (installation instruction)
  12. Coolant preheater in crankcase (installation instruction) (continued)
  13. Installation and centering of intermediate flange
  14. Removal and installation of end cover
  15. Removal and installation of oi! pan
  16. Removal and installation of cylinder head
  17. Facing cylinder head mating surface
  18. Pressure-testing cylinder head

Crankshaft assembly

  1. Checking, renewing and tightening connecting rod bolts
  2. Reconditioning and squaring connecting rods
  3. Removal and installation of pistons
  4. Renewal of piston rings
  5. Checking and reconditioning of crankshaft
  6. Mounting of crankshaft
  7. Replacing front crankshaft radial sealing ring
  8. Replacing rear crankshaft radial sealing ring
  9. Removal and installation of hub, vibration damper and V-belt pulley
  10. Checking and correcting adjustment of TDC transmitter
  11. Removal and installation of driven plates
  12. Renewing ring gear

Engine timing, valve train

  1. Checking and replacing hydraulic valve clearance compensating elements
  2. Checking and correcting basic position of hydraulic valve clearance
  3. Checking and adjusting camshaft timing
  4. Removal and installation of camshafts
  5. Grinding camshaft bearing journals
  6. Removal and installation of rocker arms
  7. Removal and installation of valve springs
  8. Checking valve springs and valve spring preload
  9. Replacing valve stem seals
  10. Checking and machining valves
  11. Checking, replacing valve guides
  12. Replacing valve seat rings
  13. Replacing valve seat rings (continued)
  14. Decoking valves
  15. Removal and installation of chain tensioner
  16. Replacing timing chain
  17. Removal and installation of tension rail
  18. Removal and installation of tension rail (continued)
  19. Removal and installation of intermediate gear for distributor drive
  20. Removal and installation of return sprocket

Mechanical gasoline injection system CIS

  1. Additional Designations for Models and Components
  2. Model and Components Survey
  3. Vehicle Characteristics
  4. Influencing Parameters of Mechanical/Electronic Mixture Adaptation
  5. Influencing Parameters of Mechanical/Electronic Mixture Adaptation (continued)
  6. Function Diagram CIS-E Injection System
  7. Testing on/off ratio
  8. Testing, adjusting engine
  9. Testing electronic idle speed control
  10. Testing fuel pressures and internal leakage
  11. Testing electrical components of CIS-E injection system
  12. Testing electrical components of CIS-E injection system (continued)
  13. Testing starting valve control
  14. Performing cold start
  15. Electrical wiring diagrams
  16. Checking fuel pump
  17. Checking injection valves
  18. Checking, renewing throttle valve switch
  19. Conducting fuel quantity comparative measurement
  20. Conducting fuel quantity comparative measurement (continued)
  21. Conducting fuel quantity comparative measurement (continued)
  22. Removal, reinstallation of fuel distributor
  23. Renewing sealing ring for control piston
  24. Renewing sealing ring for control piston (continued)
  25. Removal, reinstallation of insulating sleeve
  26. Renewing air flow sensor
  27. Renewing air flow sensor (continued)
  28. Removal, reinstallation of throttle assembly
  29. Renewing, centering sensor plate and checking and adjusting zero
  30. Removal, reinstallation of CIS-E control unit
  31. Removal, reinstallation of idle speed control unit
  32. Renewing electrohydraulic adjusting element
  33. Renewing electrohydraulic adjusting element (continued)
  34. Renewing rubber buffer for fuel pump assembly
  35. Renewing rubber buffer for fuel pump assembly (continued)
  36. Removal, reinstallation of fuel accumulator
  37. Removal, reinstallation of fuel filter
  38. Removal, reinstallation of fuel pump
  39. Renewing check valve for fuel pump

Air intake, air cleaner, turbocharger

  1. Removal, reinstallation of air cleaner
  2. Renewing intake scoop

Belt drive

  1. Instructions concerning V-belt replacement and tensioning
  2. Replacing and tensioning V-belt

Intake and exhaust manifold, emission control

  1. Identification features
  2. Function of emission control system
  3. Checking oxygen sensor failure indicator
  4. Removal, reinstallation of catalytic converter
  5. Removal, reinstallation of air pump
  6. Removal, reinstallation of electromagnetic clutch
  7. Removal, reinstallation of intake manifold, renewing gaskets
  8. Intake manifold removed (14-450)
  9. Removal, reinstallation of exhaust manifold
  10. Renewing transverse pipe
  11. Survey exhaust manifolds
  12. Checking exhaust gas recirculation (EGR)
  13. Checking air injection
  14. General instructions for vehicles with catalytic converter

Electrical system engine

  1. Instructions regarding work on breakerless transistorized ignition
  2. Function of electronic ignition system with electronic timing
  3. Testing ignition timing
  4. Analyzing oscilloscope images
  5. Renewing spark plugs
  6. Removing and installing high voltage distributor
  7. Testing electronic ignition system with electronic timing adjustment

Engine lubrication

  1. Oil circuit
  2. Oil pressure, valves in oil circuit, oil filter and thermostat (model 126)
  3. Removal and installation of oil filter
  4. Removal and installation of oil pump
  5. Removal and installation of oil pressure relief valve
  6. Checking oil level indication
  7. Removal and installation of oil level transmitter

Engine cooling

  1. Coolant circuit and engine cooling
  2. Draining and filling-in of coolant — antifreeze table
  3. Draining and filling-in of coolant — antifreeze table (continued)
  4. Removal and installation of coolant thermostat
  5. Removal and installation of coolant pump
  6. Reconditioning of coolant pump
  7. Sealing coolant pump
  8. Viscofan clutch
  9. Removal and installation of radiator
  10. Repairing radiator
  11. Checking expansion tank cap

Engine suspension

  1. Removal and installation of front engine mount
  2. Removal and installation of rear engine mount
  3. Removal and installation of engine shock absorber

Throttle control

  1. Checking, adjusting accelerator control
  2. Removing and installing engine longitudinal control shaft
  3. Removing and installing, adjusting firewall accelerator control shaft
  4. Removing and installing, renewing accelerator pedal
  5. Greasing accelerator control linkage and shafts
  6. Greasing accelerator control linkage and shafts (continued)
  7. Instructions for test and repair work
  8. ABS/ASR and electronic accelerator input test
  9. Testing electronic accelerator
  10. Testing cruise control (vehicles with ASR)

Fuel system

  1. Function of fuel tank with steadying bowl
  2. Function of fuel tank with steadying bowl (continued)
  3. Function of fuel tank venting
  4. Removing and installing fuel tank
  5. Removing and installing fuel expansion tank (Model 107)
  6. Removing and installing fuel gauge sending unit
  7. Removing and installing fuel gauge sending unit (continued)
  8. Removing and installing fuel gauge sending unit (continued)
  9. Function of fuel cooler

Exhaust system

  1. Removing and installing exhaust system