Replacement of holder for fuel pump, fuel filter and fuel reservoir

For renewing holder, remove fuel reservoir (07.3-270), fuel filter (07.3-275), fuel pump (07.3-280).

Holder has been modified to improve installation position and to increase rigidity.

Model 107, 123

A Former version

B Present version

On model 126 the shape of the fuel line between pump, filter and reservoir has also been modified.

Start of series production: November 1981.

Model 126

A Former version

B Present version

07.3.2 lla-281/1

F2

In front of fuel filter (21) is an additional pressure compensating valve (27), which closes in the event of pressure in system. If the fuel volume in system is re­duced when the fuel is cooling down, the pressure compensating valve will open. This will prevent that the control piston in fuel distributor will be pulled to full load under influence of vacuum, since other­wise during a cold start the full fuel quantity might be injected for a short period and the engine might be excessively enriched.

B. Scope

On models 107 and 126 fuel filters will be installed with damper (86), as well as a diaphragm damper (95). This will reduce noises caused by fuel pump.

86     Fuel filter with damper

87     Fuel pump

95 Diaphragm damper

On vehicles in national version (*vs)(±y(j£) and(usA) with CIS injection system prior to model year 1981, the respective components can also be installed. On vehicles of model year 1981, the changes are already in place. However, the fuel pump assembly differs by a fuel filter of larger diameter (owing to revised maintenance intervals).

Model

Starting chassis end no.

Remarks

107.022 107.042

010166 010715

Fuel filter with damper and diaphragm damper (since April 1981)

Fuel filter with damper (since April 1980)

126.022/023

004661

126.022/023

016862

Diaphragm damper (since October 1980)

On vehicles with lower chassis end no. the components can be subsequently installed in the event of complaints about “Fuel pump loud”.

07.3.2 I la-282/2 F2

Clamp for hose lines

000 589 40 37 00

Designation

Part no.

Conversion kit

Steel line for engines with light alloy fuel distributor

123 470 05 93 126 470 01 64

Responsible for delivery: Plant 50 (PEW Sindelfingen)

When exchanging fuel filter (21), fuel pump (22) or pressure compensating valve (27) make sure that a plastic sheet or plastic sleeve is mounted between these parts and holder (6, 15, 28). Sleeve should project on both sides of holder, since direct contact of parts with holder may lead to contact corrosion.

On vehicles in (aus)and (T) version, a pressure compen­sating valve may not be subsequently installed.

07.3.2 I la-283/3 F2

Former layout

14 Pressure reservoir

21   Filter

22  Fuel pump 24 Damper

Present layout

6 Holder for fuel pump and filter 1 2 Leak line

14  Pressure reservoir                  _w

15  Holder for pressure reservoir” 19 Fuel hose

21   Filter

22  Fuel pump

24 Damper

26  Fuel pressure line

27  Fuel compensating valve

28  Clamp for pressure compensating valve

29  Closing cone

30  Coupling nut

For conversion, the following parts may be used again:

Fuel pump, suction damper, pressure reservoir, fuel filter.

1    Unscrew protective case.

2   Disconnect electric connections.

3   Pinch fuel suction hose (1) between fuel tank and suction damper by means of a clamp.

07.3..2 lla-282/4 F2

4   Loosen suction hose on suction damper and pull off.

5   Unscrew fuel pressure line from feed line to engine compartment. Clean screw connection first.

6   Unscrew fastening nuts of anti-vibration buffers and remove “fuel pump assembly”.

7   Disassemble fuel pump assembly.

8 Clean fuel pump and fuel filter externally and mount in addition to plastic sleeve (slip up to bead of pump).

As an exception, a sheet (e.g. Tesafilm) may be glued on instead of plastic sleeve.

Attach plastic sleeve or sheet always in such a manner that it projects on both sides of holder. A direct con­tact of holder and pump or filter may lead to contact corrosion.

9 Assemble with components of conversion kit pump assembly, as shown in illustration. Slip fuel pump (22) up to bead into holder (6) and mount clamp (28) for pressure compensating valve (27) under holder of pressure reservojr. Prior to tightening screws of holder, position fuel pressure line (26) at pump, filter and pressure reservoir, align parts in relation to each other and tighten screws. On pressure reservoir, close the off-center connection with a closing cone (29) and a coupling nut (30).

10    Install pump assembly and fuel hoses, and make electrical connections.

11    Remove clamp on suction hose, run engine and check system for leaks.

12    Mount protective case. Then make sure that fuel hoses are not exposed to chafing.

Note: On vehicles with auxiliary heater, the leak line is approx. 50 mm in front of suction damper. Insert a T-fitting. Here, the protective anti-chafing hose must be shortened.

07.3.2 lla-282/5 F2