Removing and installing radiator
WIS 20-4200
Preceding work: Operation no. of operation texts and work units or standard texts Fan shroud removed (20–34–00). and flat rates 20-3865~-4535
A. Model 124
Coolant atradiator ………05.68. se eeeee drain (20-0100). Air scoop (89) wwe ce eee eee . take off, fit on. Clips (33) of radiator cover …….—55 see take off, fit on.
ute §=RA 20.1234-4200/1
If automatic transmission fitted: unbolt oil pipes (7) and (8), bolt on (20 Nm). Coolant hoses (10), (11) and (12) take off, fit on. Fiat shaped springs (15) pull off upward, fit on. Radiator (4) remove upward, install.
Note
The securing studs of the radiator must be inserted into the rubber pads (19) of the bottom cross member when installing. Cooling system fill, bleed (20-0100). If autornatic transmission fitted: ………..05 check oil level, adjust to correct level. LeaktightneSS 6.2… cee ee eee ee ven eewes check.
7 mm wrench socket hexagon on flexible Hazet, shaft for hose clip with worm drive 42853 Rernscheid Order no. 426–7
ota = AA 20,1234-4200/2
B. Model 129
Preceding work: Operation no. of operation texts and work units or standard texts Fan shroud removed (20-3400) and flat rates: 20-3865-4535
Coolant at radiator 22… 0… eee drain (20-0100). Coolant hoses (9), (10), (11) and (12) .. 0… ee take off, fit on. Hf automatic tansmission fitted: unbolt oil lines (7) and (8), bolt on (20 Nm). Ai SCOOP 6. cece eee eee wae remove, install. Strut (1) and cross member cr 2) cee eee eee » -unbolt, bolt on. WAG fitted: 0 cece eee detach bracket, air conditioner line at front, bottom left, bolt on. WAC fitted: 2.0.2… 00, vee eee eee tea unbolt condenser (3) at radiator (4), bolt on.
ote = RA 20.1234-4200/3
Condenser (3) …….. ce eee eee eee raise, lift out of mounts (4b) at radiator (4).
Note Push both rubber mounts (4a) onto condenser 3) at bottorn (arrow), stick on. When installing radiator, raise condenser (3) and insert into mounting plate (4b) at radiator (4). Fradiator (4) 2. ee eee ee : remove upward, install.
Note
The securing studs of the radiator must be inserted into the rubber pads (19) of the bottom cross member. Cooling systeM 6 eee ee eee fill (20-0100). If automatic transmission fittled: …………. check oil level, adjust to correct level. Cooling system …. seen seen nes check for leaks (20-0170).
7 mm wrench socket hexagon on flexible e.g. Hazet, shaft for hose clip with worm drive 42853 Rernscheid Order no. 426–7
othe = RA 20.1234–4.200/4
C. Model 140
Operation no. of operation texts and work units or standard texts and flat rates: 20-3865-4535
Fan shroud (6) ……..65 sence sete ee remove (20-3400). Coolant at radiator (4) 2… 0… ee ce ee drain (20-0100). Coolant hoses (8), (10), (14) and (12) take off, fit on. If automatic transmission fitted: …………. unbolt oil pipes (7) and (8) at radiator (4), bolt on (20 Nm). AIP SCOOP 6. ee ee remove, install.
thie RA 20.1234-4200/5
Plastic strips (13) at radiator (4) …………. pull off, fit on. Bowden cable of hood lock at radiator (4) detach, attach. If AC fitted: unbolt radiator (4) at condenser (3), bolt on. Radiator (4) remove upward, install.
Note The securing studs of the radiator must be inserted into the rubber pads (19) of the bottom cross member. Fan shroud (5) install (20~3400). Upper frame cross member (2) bolt on.
Note If new radiator (4) fitted, adjust positioning bar (20) with adjusting screw (21) by hand. To do this, turn adjusting screw (21) with upper frame cross member (2) installed until adjusting bar (20) is resting slightly pretensioned against the upper frarne cross member (2). Cooling system ……..0. Leeee see eee os fill (20-0100). If automatic transmission fitted: ……….0.. check oil level, adjust to correct level. Cooling systeM ow ee ee eee check for leaks (20-0170).
Tightening torques in Nm
7 mm wrench socket hexagon on flexibie e.g. Hazet shaft for hose clip with worm drive 42853 Remscheid Order no. 426–7
othe = RA 20.1234-4200/6
D. Models 202, 210
Preceding work: Operation no. of operation texts and work units or standard texts Fan shroud removed (20-3400). and flat rates: Model 210 with automatic transmission: viscous fan clutch 20-3865–4535 removed (20-3120)
Coolant at radiator cee eee drain (20-0100). Coolant hoses (10), (11) and (12) ………… take off, fit on. If automatic transmission fitted: …………. unbolt oil pipes (7) and (8), bolt on (20 Nrn). Plug oil pipes (7) and (8) with connection fitting, see note. Fan grille (20) 2.6… eee ee eee sees remove, install. Model 202: ……..0. denen eee see eae remove radiator cover (22), install. Flat shaped springs (15)… eee eee pull off upward, fit on. Upper frame cross member (2) ……….00unbolt, bolt on (9 Nm).
otin = RA 20.1234-4200/7
Model 210: 2… ee eee detach Bowden cable of hood lock at upper frame cross member (2), attach. Model 202: 20… ce ee eee pull off shaped rubber strip (23), fit on.
Intake air scoop (21) …… cece e eee eee remove, install. WAC fitted: oe eee eee eee unbolt condenser at radiator (4), bolt on. Radiator (4) ………. see e eee ee eee remove upward, install.
Note
The securing studs of the radiator must be inserted into the rubber pads (19) of the bottom cross member when installing. Cooling system ….. see see eee eens fill (20-0100). If automatic transmission fitted: …………. check oil level, adjust to correct lavel. Cooling system ….. sce enw teen eee check for leaks (20-0170).
7 mm socket wrench hexagon on flexible @g. Hazet shaft for hose clip with worm drive 42853 Remscheid Order no. 426–7
atime §=RA 20.1234-4200/8
Note Plug autornatic oil pipes with connection fiting (01) (shop-made).
P20-5319–13
asin = RA 20.1234-4200/9









