Contents Programed Repairs

WIS Prog_Repairs-mech2

Additional subjects are contained in the microfilms Up-to-date trouble diagnosis or Trouble diagnosis.

01 Cylinder head, oil sump

Coordinates

External oil leakage 2.6.6… ee eee B 17 Oil leakage, rear right (driving direction) between cylinder head and cylinder head gasket, engines 601, 602.91, 603.91/96 …….-.-.5.22-05D 17 Coolant leakage to outside at rear left of cylinder head gasket, engine 601 …. E 17 Coolant loss at cylinder head gasket to outside or to inside, engines 601,603 . G 17 Engine oil in cooling system, engines 601, 602,603 …………-.-0006H 17 Oil leak at gasket between boost air distribution pipe and cylinder head Engines 602.96, 603.96 (Turbo) 000–0… ee eee eee eee K 17 Engine has blue exhaust, clatters, runs roughly Engines 602.96, 603.96 up to 31.3.94 2.0.02… 2. eee ee ee eee L 17

IPR 01.10/17

Programed Repairs Engines 601, 602, 603

Mechanical I!

Operation no. of operation texts and operation values or standard texts and flat rates

01 Oil leakage

Complaint:

External oll leakage

Cause/Remedy:

In the event of external oil leakage, whose cause cannot be identified with certainty, proceed as follows:

Clean area to be tested removing all oil, dry and spray with „MB contrast spray, white”, part no. 000 989 03 59.

Allow engine to run, oi! leakage becomes visible after 2 – 5 min.

Seal point as required.

ole PR 01.1014/1

Complaint:

Oil leakage, rear right (driving direction) between cylinder head and cylinder head gasket Engines 601.911

Cause/Remedy:

Contents Programed Repairs – rysunek

The following engines produced before 10/84 up to the engine end numbers listed are affected: Manual transmission 028239 Automatic transmission 003360

Oil return hole in cylinder head gasket does not have beaded sheet metal edge.

Contents Programed Repairs – rysunek

Install new cylinder head gasket part no. 601 016 05 20 with beaded sheet metal edge around oil return hole (arrow).

Engines 601 as of 11/84, 602, 603.91/96 Install cylinder head gasket with Viton seal at oil return port and silicone sealing strip (arrow).

Prod. breakpoint: engine 602.96 05/89 engine 602.91 09/89 engine 603.96 10/88 engine 603.91 09/88

Gm PR 01.1014/2

Complaint:

Coolant toss to the outside at rear left of cylinder head gasket

Engine 601

Cause/Remedy:

The coolant flows out at the rear left, runs through the inclined position of the engine at the separation point of cylinder head/crankcase on to the right-hand side of the engine and then down through the crankcase.

Replace cylinder head gasket.

The following engines may be affected (period April-May 1988):

Model Engine Vehicle ident end no. from

124.120 601.912 A 746469 ™>T> 760958 124.180 601.912 F 074743 077264 201.122 601.911 A 446573 449045 F 501053 509117

time PR 01.1014/3

Complaint:

Loss of coolant at cylinder head gasket to outside or to inside

Engines 601, 603

Contents Programed Repairs – rysunek
Contents Programed Repairs – rysunek

Cause/Remedy:

Gaskets from the following period are affected: Engine 601 as of 01/85 up to 08/85 Engine 601 as of 01/85 up to 01/86

When installed, the gasket on engine 603 is recognizable from the straight web (arrow, A) and on engine 601 from the recessed web (arrow, B).

The cylinder head gasket may be torn both to the inside as well as to the outside (see ill.). P01-0247–13

If a loss of coolant exists, it is essential on these engines to check the cylinder head gasket for leaks (Repair instructions 01-015 and 01-020, respectively). If the cylinder head gasket is torn through to the inside into the combustion chamber, the piston projection must be measured before fitting a new cylinder head gasket (see Repair Instructions 03-316). (Possible initial damage to conrod as a result of water hammer.)

Vehicles affected

Model Engine Vehicle ident end no. from to

124 601 A 010408 A 113431 F 000485 F start of production

603 A 010408 A 184855 F 003891 F start of production

201 601 A 192572 A 261897 F 078457 F 166815

Complaint:

Engine oil in cooling system

Engines 601, 602, 603

Porous cylinder head in the area of the front oil passage for supplying oil to first camshaft bearing or of hydraulic valve clearance compensating elements.

Replace cylinder head. Clean cooling system (Repair Instructions 20-015).

Note It is not always possible to detect this leakage when pressure-testing the removed cylinder head.

eile PR 01.1014/5

Complaint:

Oli leak at gasket between charge air manifold and cylinder head

Engines 602.96, 603.96 (turbo)

Cause/Remedy:

As of approx. 07/90 surface spalling may occur at the joint of the first piston ring. The cylinder wall is damaged as a result and the scavenging quantity is increased. As a result, oil is entrained into the engine ventilation and flows out of the gasket of the charge air manifold. Damaae code for warranty/goodwill: 01 002 11 scoring on crankcase cylinder bore.

Illuminate engine/determine findings. Production breakpoint Modified piston rings installed since 11/91.

AN Slight oil leakage (sweating) at gasket between charge air manifold and cylinder head corresponds to present status of series production. Refer to Up-to-date Troubleshooting 14-92121.

Production breakpoint of modified piston rings

Engine Engine end no. Engine end no. manual transmission automatic transmission

602.961 006373 009855 602.962 015352 011326 603.960 – 036342 603.963 – 003189

time PR 01.1014/6

Complaint:

Engine has blue exhaust, clatters, runs roughly

Engines 602.96, 603.96 up to 31.3.94

Contents Programed Repairs – rysunek

Cause/Remedy:

Cylinder head gasket leaking in area of oil cross gallery to cylinder 1.

1 Determine condition and inspect engine with inspection lamp, if necessary.

2 Replace cylinder head gasket (01-415).

A. Before installing cylinder head, always deburr the oil cross gallery and chamfer the edges, respectively.

P01.30-0202–15

seid PR 01.1014/7