Contents Programed repairs
WIS Prog_Repairs-mech3
Additional subjects are contained on the microfilms Up-to-date Trouble diagnosis.
03 Crank assembly
Ticking noises at idle speed on vehicles with low mileage (< 10 000 km). Especially loud with cold engine 0.0.0.0… 0. cee eee B 17 Ticking noises from about 1500 rpm when engine cold and warm, also heard while driving 2.6.0… ee eee eee D 17 Ticking noises from about 1500 rpm when engine cold and warm, also heard while driving 2.2.2… 2… ee ee ee eens G 17 Replacing front crankshaft radial seal …………….22202–2—-00– H 17
IPR 03.10/1
Programed Repairs Engines 601, 602,603 Mechanical Ill
| 03 Pistons Additional subjects are contained in the microfilms Up-to-date trouble diagnosis or Trouble diagnosis. | ||
| Complaint: Ticking noises at kdle speed on vehicles with low mileage (< 10 000 km). Especially loud with cold engine Engines 601, 602, 603 | ||
| Cause/Remedy: Noises may occur on engines from production period 08/84 — 03/85. | ||
| Engine | starting with engine end no. | up to engine end no. |
| 601.911 | 10.028240 12,003361 | 10.092787 12.008973 |
| 601.912 | from start of series | 10.008804 12.000033 |
| 602.911 | from start of series | 10.000151 12.000069 |
| 602.912 | from start of series | 10.000494 12.000099 |
| 603.912 | from start of series | 10.001931 12.001480 |
PR 03.10/1
Loud piston reversal noises in cylinder at TDC when pistons change direction.
To exclude valve contro! noises from the hydraulic valve clearance compensating elements, allow engine to run for approx. 7 min. at 3000 rpm. If the noise is caused by the pistons, it should still be heard.
These noises were eliminated by changing the shape of the piston.
In the event of a complaint, install modified pistons part no. 601 030 08 17 after consulting ZKD-G.
Complaint:
Ticking noises at approx. 1500 rpm with cold and warm engine, also heard
while driving
Engines 601, 602, 603
Cause/Remedy:
These noises may occur on engines from production period middie of 01/86 to 02/86.
PR 03.10/2
Engine starting with engine end no. up to engine end no.
601.911 10.138770 146025 12.013450 014087 601.912 10.029984 034605 12.002364 002780 602.911 10.012781 014877 12.002800 003686 602.912 10.017565 022759 12.002830 003741 603.912 10.010330 012569 12.006272 007615
Loud piston reversal noises in cylinder at TDC when pistons change direction. To exclude valve control noises from the hydraulic valve clearance compensating elements, allow engine to run for approx. 7 min. at 3000 rpm. If the noise is caused by the pistons, it should still be heard.
These noises were eliminated by changing the shape of the piston.
In the event of complaints, consult ZKD-G.
PR 03.10/3
Complaint:
Ticking noises from about 1500 rpm when engine cold and warm, also heard while driving Engines 601, 602, 603
Cause/Remedy:
The following engines may be affected: Engine as of engine end no. up to engine end no.
| 601.911 | 10.028240/12.003361 | 10.196278/12.018007 |
| 601.912 | as of start of series prod. | 10.060313/12.005066 |
| as of start of series prod. | 10.034400 up to 12/86/12.008286 | |
| as of start of series prod. | 10.051330/1 2.008634 | |
| as of start of series prod. | 10.023961/12.014718 |
Cause Connecting rod shaft offset too large relative to plane faces of small and large eye. This causes loud piston reversal noises in cylinder when pistons change direction in TDC range. Remedy Install connecting rods made of modified material, part no. 601 030 36 20. in addition, likewise replace pistons which, apart from the code figure 08, do not have any of the stamped letters „L”, „M”, „N”,”O”, „S” or „T”.
AN The code letters „A, X, B” are group code letters which refer to the piston or cylinder diameter. They must not be confused with the letters listed under Remedy.
PR 03.10/4
Complaint:
Replacing front crankshaft radial sealing ring. Engines 601, 602, 603
Cause/Remedy:
{f oil leakages occur at the front of the crankshaft, it is only necessary in the most fraquent cases to replace the crankshaft radial sealing ring. Replacing hub at the same time is only necessary in those cases where two wear tracks (grooves) are visible on the hub. For hubs which have only one wear track (groove) a radial seal with a sealing lip offset 2 mm to the rear is available (repair version). If the sealing surface of the hub is only ground bright, only the standard version of radial seal may be fitted. PO3-6002–13
Note Press the radial seal dry (without grease) into the timing case cover and coat the sealing lip (Fig., item 1) with engine oil – do not use grease.
PR 03.10/5
