Testing, adjusting engine

WIS 07.1-1100

Testing, adjusting engine – rysunek

Preceding work: Operation no. of operation texts and work units or standard texts and flat rates: 07-1100

Coolant level 2.0.0… ee eee check, correct. Engine oil level 2… 2… eee eee ee eee check; pay attention to condition of oil (visual inspection). Air filter element 2.2.20… 0.00 eee eee remove, install (visual inspection). Testers (001, 013, 017) 0.2… eee ee ee connect. Pulse generator (021) ………….00 000 connect.

iin = RA 07.1.1044-1100/1

Accelerator control linkage …………….4. check ease of movement, condition. Lubricate bearing points, relay levers, ball sockets. Full throttle stop 22… 2. ee eee ee ee eee check from accelerator pedal, adjust Bowden cable if necessary. Idle stop check; adjust at Bowden cable if necessary. Voltage at battery ……………….00.0. test. Specification min. 11.5 volts. warm up to operating temperature (coolant Engine 2.0… ee eee ee eee eee temperature approx. 80 °C). Air conditioner or automatic climate control ….. switch off. Idle speed 6. ee eee check, adjust if necessary. Unplug connector from actuator, plug in. Start of delivery 2.2.0… eee ee ee ee test with digital tester. Max. speed at no load …………..00 000 test. Injection timer 2.0.6… ee eee ee eee test. Electronic diesel system (EDS) …………. test with pulse counter (013), see (07.1~-1120). Anti-jerk control (ARA) 2… 6… ee ee ee eee test with pulse counter (013), see (07.1-1841.)

auiiis = RA 07.1.1044-1100/2

Testing, adjusting engine – rysunek

Test and setting data

Testing, adjusting engine – rysunek
Testing, adjusting engine – rysunek
Testing, adjusting engine – rysunek
Testing, adjusting engine – rysunek

Special tools

wie = RA 07.1.1044-1100/3

Testing, adjusting engine – rysunek
Testing, adjusting engine – rysunek

Connection diagram for testers with adapter 017 RI generator 001 Digital tester 010 Adapter 021 TDC pulse generator o11 Trigger clarnp 2 Governor 015 Test cable with connector ai RI generator pin 016 Diagnostic socket 59 TDC generator pin

coum RA 07.1.1044-1100/4

1 Check coolant level, correct if necessary.

2 Check engine oil level, paying attention to condition of oil (visual inspection).

3 Remove air filter element (visual inspection), and install.

4 Connect testers (013, 001, 017) according to connection diagram.

5 Gonnect pulse generator (021).

Testing, adjusting engine – rysunek

6 Check accelerator control for ease of movement and condition. Lubricate bearing points, relay levers and ball sockets.

7 Check full throttle stop from accelerator pedal; adjust at adjusting screw (229) if necessary.

Engine 602.96

equim = RA 07.1.1044-1100/5

Testing, adjusting engine – rysunek
Testing, adjusting engine – rysunek

Engine 603.96

8 Check idle stop. The spring plate (226) of the Bowden cable (230) must be resting against the compression spring (227) free of tension.

Testing, adjusting engine – rysunek

Engine 602.96

Testing, adjusting engine – rysunek

Engine 603.96

Adjust Bowden cable (230) with adjusting nut (232) from the car interior, if necessary.

pie = RA 07.14.1044-1100/6

9 Test voltage at battery. Specification: at least 11.5 V.

10 Raise engine to operating temperature (coolant temperature approx. 80 °C).

41 Switch off air conditioner or automatic climate control.

Testing, adjusting engine – rysunek
Testing, adjusting engine – rysunek

Test idling speed. Unplug 2-pin coupling at actuator, plug in. Set idling speed by slackening locking nut (arrow).

Test start of delivery dynamically, read off on digital tester (07-8244).

12 Test „max. speed” without engine load.

Test injection timing device without load. 1s Ww

14 Te t electronic diesel system, see (07.1 120).

eatin RA 07.1.1044-1100/7