Checking decel shutoff

WIS 07.3-140

Test values

Speed km/hEngine speed 1/min without refrigerant compressorwith refrigerant compressor
> 35> 1100> 1300
Conventional toolsSe
Revolution counter, volt-cohmmeterOS
Digital multimeter with means for measuring AC (for impulse transmitter test)Oe

Note Since dece! shutoff requires engine speed impulses and driving speeds, the respective component can be tested only on a dynamometer or on the road.

A function test of impulse transmitter can also be made by means of workshop oscilloscope Bosch MOT 300/ 400, 202 and SUN 1080, 1019, 2110 in position “Primary, special ‘‘or ‘‘Generator test’’.

Testing on dynamometer

Remove air cleaner.

Run on dynamometer at approx. 70 km/h in 4th speed or driving position ‘‘D’’. Release accelerator pedal, air flow sensor plate will move into zero position. As soon as combustion starts again at approx. 1100/min or approx. 1300/min with refrigerant compressor, the air flow sensor plate will move into idle position. Check decel shutoff valve and its activation, if required.

Testing without dynamometer (road test)

Run engine at idle.

Test decel shutoff valve (30).

Test activation of switchover valve (43a).

Test speed-dependent control.

Checking decel shutoff – rysunek

Testing

Testing decel shutoff valve (30)

1 Run engine at idle. Pull off vacuum lines on switch over valve (43a) and connect with each other. Decel shutoff valve (30) will then open and the engine should stop. If engine keeps running, check vacuum lines, Intake manifold vacuum should be available at idle. If vacuum is available, replace decel shutoff valve (30).

Layout switchover valves (43a)

Checking decel shutoff – rysunek
Checking decel shutoff – rysunek

Model 107

Checking decel shutoff – rysunek

Model 123

Model 126 43 Switchover valve air conditioning (identification: green cap} 43a Switchover valve decel shutoff (identification: gray cap)

Checking decel shutoff – rysunek

Checking activation of switchover valve

2 Pull off fuel pump relay. Bridge jack 7 (terminal 87) and 8 (terminal 30), so that fuel pump will run. Start engine, connect jack 5 (terminal 87 S) of coupler with battery voltage. Engine should now stop.

Checking decel shutoff – rysunek

If engine does not stop, check microswitch (3 or 6) or switchover valve (43a or 5).

Electronic fuel pump relay Ton Switchover valve Microswitch Tachometer transmitter

Testing microswitch (3)

Checking decel shutoff – rysunek

Pull off coupler on microswitch. Connect ohmmeter.

Readout: At idle 0 2 When accelerating o 22.

Check adjustment of slotted lever, if required. Roller in slotted lever should rest free of tension against final stop. Check rotary spring (arrow), if required.

Checking decel shutoff – rysunek

Testing switchover valve (43a)

Checking decel shutoff – rysunek

Pull coupler from microswitch (3) and connect cable, color black/green, to battery voltage, engine should now stop. If engine does not stop, test line with an ohmmeter for passage or replace switchover valve (43a).

Layout switchover valves (43a)

Checking decel shutoff – rysunek

Model 107

Checking decel shutoff – rysunek

Model 123

Model 126 43 Switchover valve air conditioning (identifiaction: green cap) 43a Switchover valve decel shutoff {identifiaction: gray cap)

Checking decel shutoff – rysunek

3 Check cutting-in impulse of refrigerant compressor. For this purpose, run engine at idle. Connect positive cable (red) of voltmeter to jack 3 (terminal KL) and negative cable (black) to jack 11 (terminal 31).

When switching-on refrigerant compressor, battery voltage should be available.

If no voltage is available, test line blue/gray/red (terminal KL) to refrigerant compressor for interruption.

Checking decel shutoff – rysunek

Note: With air-conditioning system switched on, voltage should be available at jack 3 (terminal KL) O,75bl/gr rt —>e of fuel pump relay (refer to wiring diagram group 83 air-conditioning system).

1 Fuel pump relay e Refrigerant compressor

Test speed-dependent control

4 Pull coupler from switchover valve (43a) and connect voltmeter to coupler. Operate on dynamometer or on road in 4th gear, or in driving position ‘’D” at 70 km/h. Release accelerator pedal, battery voltage should be available. If there is no voltage, test impulse transmitter on tachometer or replace fuel pump relay, if required.

There should be no voltage below approx. 1100/min or approx. 1300/min with refrigerant compressor.

Testing impulse transmitter on tachometer

Checking decel shutoff – rysunek

5 A prerequisite for a signal is that the speed indicator is Operational.

Test impulses for decel shutoff. Pull off fuel pump relay for this purpose.

Electronic tachometer

a) Testing output signal

Checking decel shutoff – rysunek

Connect digital multimeter (position V = DC). For this purpose, connect positive cable (red) to jack 9 (terminal 15), grounding cable (black) to jack 1 (terminal V).

Attention! Perform measurements in position V = only. Wrong handling will damage tachometer electronics.

Checking decel shutoff – rysunek

Bridge jack 7 (terminal 87) and jack 8 (terminal 30), fuel pump will then run.

Checking decel shutoff – rysunek

Operate on dynamometer or on road in 4th gear or in driving position ‘‘D‘’ at 70 km/h. Readout should indicate 2 1 Volt DC (in position V =). Measuring value increases with increasing vehicle speed.

If there is no readout, test cable from jack 1 (terminal V) to impulse transmitter connection (3) by means of an ohmmeter for passage.

Model 107, 126 3 Impulse transmitter connection

Test speed readout of tachometer.

Checking decel shutoff – rysunek

If there is no readout, remove instrument cluster. Remove 8-pole plug on tachometer.

b) Testing input signal

Connect digital multimeter with means for measuring AC {in position V ~ or V ~*~ ) to jack 5.

Red positive (jack 5) ul Black vehicle ground

Checking decel shutoff – rysunek

Operate on dynamometer or on road in 4th gear or in driving position “D“ at 70 km/h. Readout 2 should amount to 1 Volt AC (in position V ~). Measuring value increases with increasing driving speed.

If there is no readout, test cable for passage by means of an ohmmeter or replace cable or impulse transmitter (arrow) in transmission.

Impulse transmitter automatic transmission

Mechanical tachomater

Checking decel shutoff – rysunek

Connect digital multimeter with means for measuring AC {in position V ~or Y). For this purpose, connect position cable (red) to jack 1 (terminal V), grounding cable (black) to jack 11 (terminal 31).

Bridge jack 7 (terminal 87) and jack 8 (terminal 30), Wo 1074 -10616/1 fuel pump will now run.

Operate on dynamometer or on road in 4th gear or in driving position ‘‘D” at approx. 70 km/h. Readout 2 should amount to 1 Volt AC (in position V ~ ). Measuring value increases with increasing vehicle speed. speed.

\f there is no readout, test cable for passage by means of an ohmmeter. Replace cable or impulse transmitter (5) on tachometer, if required.

Checking decel shutoff – rysunek

Test resistance of impulse transmitter (5). Nominal = 650 — 1370 22.

If the nominal value is exceeded or not attained, replace impulse transmitter.

Model 123 5 Impulse transmitter

Checking decel shutoff – rysunek
Checking decel shutoff – rysunek

Function diagram decel shutoff

1 Mixture control

41 Impulse transmitter mechanical Color code ler tachometer gr =gray

2 Transistorized switching unit 3. Microswitch 43a Switchover valve vi = purple 12. Intake manifold decel shutoff ws = white

13 Slotted lever 44 Fuel pump relay

30 Decel shutoff valve To idle speed air distributor

Note: For operation of decel shutoff and idle speed stabilization refer to 07.3500.

F2

Checking decel shutoff – rysunek
Checking decel shutoff – rysunek
Checking decel shutoff – rysunek

Wiring diagram decel shutoff model 123

1 Fuel pump relay To output starter lockout and backup lamp switch Color code zeae reaogo

2 Thermo time switch Transmitter mechanical tachometer bl = blue

3 Cold starting valve Fuel pump br = brown

4 Warm-up compensator Fuse 12 terminal 15 access ge = yellow

5 Switchover valve Refrigerant compressor gn =green

6 Microswitch Cable connector engine terminal 30 gr =gray Cable connector terminal TD ts =pink Cable connector engine terminal 50 rt =red sw = black vi = purple ws = white

Checking decel shutoff – rysunek
Checking decel shutoff – rysunek
Checking decel shutoff – rysunek

Wiring diagram decel shutoff model 107, 126

1 Fuel pump relay a Cable connector engine terminal 50 Color code

2 Thermo time switch b Transmitter electronic tachometer bl =blue

3 Cold starting valve c Fuel pump br brown

4 Warm-up compensator d Fuse 14 terminal 15 access ge yellow

5 Switchover vaive e Refrigerant compressor gn =green

6 Microswitch f Cable connector terminal 30 gr =gray g Cable connector terminal TD rs pink h_ Cable connector engine terminal 50 rt =red sw = black vi = purple ws = white

Checking decel shutoff – rysunek
Checking decel shutoff – rysunek

Decel shutoff and idle speed stabilization

1 Multiple distributor 14 Bypass vaive air conditioning a To switchover valve dece! shutoff

2 Contour hose 15 Plug connection b To switchover valve dece! shutoff

3 Contour hose 16 Plug connection c To switchover valve air conditioning

4 Contour hose 17 Contour hose d To switchover valve air conditioning

5 Idle speed air distributor 20 Contour hose e Connection idle speed air

6 Contour hose 21 Contour hose f Vacuum connection intake manifold

7 Contour hose 22 Connecting hose

8 Hose clip 23 Vacuum line

9 Contour hose for air filter 30 Decel shutoff valve

10 Idle speed air screw 96 Auxiliary air valve

11 Decel circulating air valve

12 Intake manifold

13 Air guide housing