Test program (model year 1977)

WIS 14-100

Model year 1977/78/79

A. Federal version, tourist vehicles Federal version

For complaints such as: Poor warming-up characteristics of engine, poor idle speed, engine not accelerating or splashing during acceleration, check emission control system for function.

Test conditions: Engine at operating temperature, run engine at idle speed.

Test the following: EGR, air injection and fuel evaporation control system.

Test program – rysunek

Function diagram model year 1977

1 Mixture controller 39 Charcoal canister 60 Thermovalve 40 °C a_ Air injection line 2 = Ignition distributor 40 Air pump 61 Thermovalve 17 °C b Connection tank vent

9 Switch-over valve ignition 41 Diverter valve (air 74 Pressure relief valve 31° EGR valve_ switch-over valve) 75 Pressure transducer

35 Check vaive 42 Check vaive 78 Air filter for silencing 45 Air filter

14,2-100/1 USA 1977/78/79 F2

Function diagram model year 1978/79

Test program – rysunek

78 Air filter for silencing Air filter

1 Mixture controller 35 Check valve 45 Thermovalve 40 °C 80 Auxiliary air valve

2 Ignition distributor 39 Charcoal canister 60 Thermovalve 17 °C 81

5 Regenerating valve (purge 40 Air pump Contour hose 61 valve) 41° Diverter valve (air Air injection line 74 Pressure relief valve

9 Switch-over valve ignition switch-over valve) Connection tank vent 75 Pressure transducer

Test program – rysunek

31 EGR valve 42 Check valve

Testing EGR

Pull brown vacuum line from EGR valve (31) and slowly increase idle speed.

Engine runs without Engine runs irregularly starting at approx. change. 1200/min or stops.

Testing vacuum lines

Test layout of vacuum lines on pressure transducer and intake pipe.

Test program – rysunek

Note that connections on pressure transducer are identified with color rings. The attached vacuum lines should have the same color.

Test program – rysunek

Connection intake pipe vacuum (blue) a WN Connection vent line (white) Connection exhaust gas backpressure line (orange) Connection vacuum line to EGR valve (brown)

On black thermovalve 40 °C (60) the red vacuum line should be plugged to diagonal connection, and the rubber hose to straight connection. Check all pertinent vacuum lines for leaks and blow out vacuum connections.

Testing thermovalve 40 °C (60)

The thermovaive is identified by a black plastic section and the designation “50 AA 4” punched into metal section. Pull-off vacuum hose at straight connection, let engine run and accelerate.

Vacuum should be felt at free connection.

During removal and installation of thermovalve make sure that the small connecting pipes are not damaged.

=r

14.2-100/3 USA 1977/78/79 F2

Test program – rysunek

Testing pressure transducer (75)

Run engine at idle speed. Pull-off brown vacuum line on EGR vaive. Connect vacuum pressure gauge or keep vacuum line closed with finger. Vacuum should be available at idle speed.

\f there is no vacuum, renew pressure transducer.

Testing EGR valve (31)

Test program – rysunek

Run engine at idle speed. Pull-off both hoses on EGR valve.

Plug brown vacuum line to connection for red/purple vacuum line. Engine should run irregularly or come to a stop.

Test program – rysunek

\f operation of engine is not changing, renew EGR valve.

Testing air injection

Connect CO measuring instrument and read exhaust gas value. Pull vacuum line from straight connection of thermovalve (61) and close connection.

Exhaust gas value Exhaust gas value increasing. not increasing.

=P

14.2-100/4 USA 1977/78/79 F2

Test program – rysunek

Testing vacuum lines

The blue vacuum line from intake pipe should be connected to blue line and diagonal connection of thermovalve (61) by means of a distributor and check valve. The check valve should be plugged on with connection (A) in direction of intake pipe.

The blue/purple vacuum line of straight connection of thermovalve (61) leads to diverter valve (41).

Test program – rysunek

Testing vacuum

Pull vacuum line from diagonal connection of thermovalve (61), connect vacuum gauge or keep closed with finger. Vacuum should be available at idle speed. If not, test vacuum lines for leaks and blow out vacuum draw-off line (tapping line) at intake pipe.

!f vacuum is available, test thermovalve (61) and renew, if required.

Testing thermovalve 17 °C (61)

Test program – rysunek

The thermovalve is identified by a blue plastic section and the designation “50 AB 5″ punched into metal section.

Pull-off blue/purple vacuum line, run engine.

Vacuum should be available at free connection.

If thermovalve is in order, renew diverter valve (41).

W07-10895

= =P

14,.2-100/5 USA 1977/78/79 F2

Testing fuel evaporation control system

Pull black plastic line (draw-off line) to throttle valve housing from charcoal canister and keep closed with finger or connect vacuum gauge.

Slowly increase engine speed to above approx. 2000/min.

No vacuum at idle. No vacuum increase Vacuum increases at increasing speed. with increasing speed.

Test program – rysunek

1 a – –

Mode! year 1977

Testing draw-off hose

The draw-off hose should be plugged to throttle valve housing (arrow). Check hose for leaks and blow out connection on throttle valve housing.

Model year 1978/79

Testing draw-off hose and regenerating valve

The draw-off hose should be plugged to throttle valve housing (arrow). Check hose for leaks and blow out connection on throttle valve housing.

If there is still no vacuum, pull draw-off hose in front of regenerating valve and repeat test.

If vacuum is available, renew regenerating valve.

B. California version

For complaints such as: Poor warming-up characteristics of engine, poor idle speed, engine not accelerating or splashing during acceleration, check emission control system for function.

Test conditions: Engine at operating temperature, run engine at idle speed.

Test the following: EGR, air injection and fuel evaporation control system.

Function diagram model year 1977

Test program – rysunek

1 ee

1 Mixture controller 40 Air pump 61 Thermovalve 17 °C 78 Aijr filter for silencing

2 Ignition distributor 41. Air switch-over valve 73 Thermovalve 50 °C a Air injection line

9 Switch-over valve ignition 42 Check valve 74 Pressure relief valve cylinder head

31 EGR valve 60 Thermovalve 40 °C 75 Pressure transducer b_ Air injection line be-

39 Charcoal canister tween catalysts c Connection tank vent

14.2–100/7 USA 1977/78/79 F2

Function diagram model year 1978/79

Test program – rysunek
Test program – rysunek

—

1 Mixture controller 39 Charcoal canister 61 Thermovaive 17 °C 80 Auxiliary air valve 2. Ignition distributor 40 Air pump 73 Thermovalve 50 °C 81 Contour hose 5S Regenerating valve 41 Air switch-over valve 74 Pressure relief valve a Air injection line

9 Switch-over valve ignition 42 Check valve 75 Pressure transducer cylinder head

Test program – rysunek

31 EGR valve 60 Thermovalve 40 °C 78 Air filter for silencing bAir injection line between catalysts c¢ Connection tank vent

Testing EGR

Pull-off brown vacuum line on EGR valve (31) and slowly increase idle speed.

Engine runs irregularly starting at approx. continues without 1200/min or comes to stop. a stop.

14,2–100/8 USA 1977/78/79 F2

Testing vacuum lines

Test layout of vacuum lines on transducer and intake pipe.

Test program – rysunek

Note that connections on pressure transducer are identified with color rings. The plugged-on vacuum lines should have the same color.

Connection intake pipe vacuum (blue) -& WN Connection vent line (white) Connection exhaust gas backpressure line (orange) Connection vacuum line to EGR valve (brown)

Test program – rysunek

On black thermovalve 40 °C (60) the red vacuum line should be connected to diagonal connection, and the rubber hose to straight connection. Check all pertinent vacuum lines for leaks and blow out vacuum draw-off connections.

Testing thermovalve 40 °C (60)

The thermovalve is identified by black plastic section and by the designation “50 AA 4″ punched into metal section. Puill-off vacuum hose at straight connection, keep engine running and accelerate.

Vacuum should be available at free connection.

When removing and installing thermovalve, make sure that the small connecting pipes are not damaged.

14.2–100/9 USA 1977/78/79 F2

Test program – rysunek

Test pressure transducer (75)

Run engine at idle. Pull-off brown vacuum line on EGR valve. Connect vacuum gauge or keep vacuum line closed with finger. Vacuum should be available at idle speed.

If there is no vacuum, renew pressure transducer.

Test EGR valve (31)

Test program – rysunek

Run engine at idle speed. Pull-off both hoses on EGR valve.

Plug brown vacuum line to connection for red/purple vacuum line. Engine should run irregularly or come to a stop.

Test program – rysunek

lf operation of engine is not changing, renew EGR valve.

Testing air injection

Connect CO measuring instrument to exhaust gas backpressure line and read exhaust gas emission value. Change vacuum hose from straight plug connection of thermovalve (73) to straight plug connection of thermovalve (61).

Exhaust gas value Exhaust gas value clearly decreasing. not decreasing.

a a

14.2-100/10 USA 1977/78/79 F2

Test program – rysunek

Test vacuum lines

The blue vacuum line from intake pipe should be connected to diagonal connection of thermovalve (61) by means of a distributor. The purple/blue vacuum line leads from straight connection of thermovalve (61) to diagonal connection of thermovalve (73) and from straight connection of thermovalve (73) to air switch-over valve (41).

Test vacuum

Test program – rysunek

Check at straight connection of thermovalve (61) for vacuum. If vacuum is available, renew air switch-over valve (41).

If there is no vacuum:

Pull-off blue vacuum line on thermovalve (61) and check for vacuum.

’f vacuum is available:

Renew thermovaive (61).

If there is no vacuum:

Test program – rysunek

Remove vacuum line to intake pipe and blow out with compressed air.

Test thermovalve (73)

If upon completion of the above jobs the exhaust gas value is still not decreasing, test thermovalve (73) for passage and renew, if required.

Below approx. 50 °C thermovalve is open, above approx. 50 °C valve is closed.

The thermovalve is identified by black plastic section with a green color dot and 107-10895 by the designation ‘50 AA 13” punched into metal section.

Note: Starting model year 1978 the identifying color is green, designation “BO AC 13”.

=F

14.2-100/11 USA 1977/78/79 F2

Testing fuel evaporation control system

Pull-off black plastic line (draw-off line) to throttle valve housing from charcoal canister and keep closed with finger or connect vacuum gauge.

Slowly increase engine speed to above approx. 2000/min.

Test program – rysunek

No vacuum at idle. Vacuum not increasing Vacuum increasing at increasing speed. at increasing speed.

Model year 1977

Test draw-off hose

Draw-off hose must be plugged to throttle valve housing (arrow). Check hose for leaks and blow out connection on throttle valve housing.

Model year 1978/79

Test draw-off hose and regenerating valve

(purge valve)

Test program – rysunek

Draw-off hose should be plugged to throttle valve housing (arrow). Check hose for leaks and blow out connection on throttle valve housing.

If there is still no vacuum, pull-off drawoff hose in front of regenerating valve and repeat test.

If vacuum is available, renew regenerating valve (purge valve).

C. Tourist vehicles California version

For complaints such as: Poor warming-up characteristics of engine, poor idle speed, engine not accelerating or splashing during acceleration, check emission control system for function.

Test conditions: Engine at operating temperature, run engine at idle speed.

Test the following: EGR, air injection and fuel evaporation control system.

Test program – rysunek

Function diagram model year 1977

cena al

1 Mixture controller 39 Charcoal canister 60 Thermovalve 40 °C 75 Pressure transducer

2 Ignition distributor 40 Air pump 61 Thermovalve 17 °C 78 Air filter for silencing

9 Switch-over valve ignition 41. Air switch-over valve 73 Thermovaive 50 °C a Air injection line

31 EGR valve 42 Check valve 74 Pressure relief valve cylinder head c Connection tank vent

14.2~100/13 USA 1977/78/79 F2

Function diagram model year 1978/79

Test program – rysunek

Thermovalve 17 °C Mixture controller 39 Charcoal canister 61 80 Auxiliary air valve -0O00n— Thermovalve 50 °C Ignition distributor 40 Air pump 81 Contour hose 73 Regenerating valve 41. Air switch-over valve Pressure relief valve 74 Air injection line Switch-over valve ignition 42 Check valve 75 Pressure transducer cylinder head EGR valve 60 Thermovalve 40 °C 78 Air filter for silencing Connection tank vent

Testing EGR

Pull brown vacuum line from EGR valve (31) and slowly increase idle speed.

Engine runs irregularly Engine operation starting at approx. continues without 1200/min or comes to stop. a stop.

14.2-100/14 USA 1977/78/79 F2

Test vacuum lines

Test layout of vacuum lines on transducer and intake pipe.

Test program – rysunek

Note that connections on pressure transducer are identified with color rings. The plugged-on vacuum lines should have the same color.

Connection intake pipe vacuum (blue) & WN Connection vent line (white) Connection exhaust gas backpressure line (orange) Connection vacuum control line to EGR valve (brown)

Test program – rysunek

On black thermovalve 40 °C (60) the red vacuum line should be connected to diagonal connection, and the rubber hose to straight connection. Check all pertinent vacuum lines for leaks and blow out vacuum draw-off connections.

Test thermovalve 40 °C (60)

The thermovalve is identified by black plastic section and by the designation “50 AA 4” punched into metal section.

Pull-off vacuum hose at straight connection, keep engine running and accelerate.

Vacuum should be available at free connection.

When removing and installing thermovalve, make sure that the small connecting pipes are not damaged.

=p”

14.2-100/15 USA 1977/78/79 F2

Test program – rysunek

Test pressure transducer (75)

Run engine at idle. Pull-off brown vacuum line on EGR valve. Connect vacuum gauge or keep vacuum line closed with finger. Vacuum should be available at idle speed.

If there is no vacuum, renew pressure transducer.

Test EGR valve (31)

Test program – rysunek

Run engine at idle speed. Pull-off both roreiaan4 hoses on EGR valve.

Plug brown vacuum line to connection for red/purple vacuum line. Engine should run irregularly or come to a stop.

If operation of engine is not changing, renew EGR valve.

Pr “Pr

Testing air injection

Connect CO measuring instrument and read exhaust gas emission value. Change vacuum hose from straight plug connection of thermovalve (73) to straight plug connection of thermovalive (61).

Exhaust gas value Exhaust gas value clearly decreasing. not decreasing.

=F

14.2–100/16 USA 1977/78/79 F2

Test program – rysunek

Test vacuum lines

The blue vacuum fine from intake pipe should be connected to diagonal connection of thermovalve (61) by means of a distributor. The purple/blue vacuum line leads from straight connection of thermovalve (61) to diagonal connection of thermovalve (73) and from straight connection of thermovalve (73) to air switch-over valve (41).

Test program – rysunek

Test vacuum

Check at straight connection of thermovalve (61) for vacuum. If vacuum is available, renew air switch-over valve (41).

If there is no vacuum:

Pull-off blue vacuum line on thermovalve (61) and check for vacuum.

If vacuum is available:

Renew thermovalve (61).

\f there is no vacuum:

Test program – rysunek

Remove vacuum line to intake pipe and blow out with compressed air.

Test thermovalve (73)

\If upon completion of the above jobs the exhaust gas value is still not decreasing, test thermovalve (73) for passage and renew, if required.

Below approx. 50 °C thermovalve is open, above approx. 50 °C valve is closed.

The thermovalve is identified by black 3OF~10095 plastic section with a green color dot and by the designation ‘50 AA 13” punched into metal section.

Note: Starting model year 1978 the identifying color is green, designation “50 AC 13”.

of =

14.2–100/17 USA 1977/78/79 F2

Testing fuel evaporation control system

Pull-off black plastic line (draw-off line) to throttle valve housing from charcoal canister and keep closed with finger or connect vacuum gauge.

Slowly increase engine speed to above approx. 2000/min.

No vacuum at idle.Vacuum not increasing
Vacuum increasingat increasing speed.
at increasing speed.
Test program – rysunek

ee

Model year 1977

Test draw-off hose

Draw-off hose must be plugged to throttle valve housing (arrow). Check hose for leaks and blow out connection on throttle valve housing.

Model year 1978/79

Test program – rysunek

Test draw-off hose and regenerating valve (purge valve)

Draw-off hose should be plugged to throttle valve housing (arrow). Check hose for leaks and blow out connection on throttle valve housing.

If there is still no vacuum, pull-off drawoff hose in front of regenerating valve and repeat test.

If vacuum is available, renew regenerating valve (purge valve).