Adjusting idle speed

WIS 07.2-100

Identification: Information plate in national language on cross member in front of radiator or on cylinder head cover. Adjust engines according to data of respective emission control information plate.

Testing and adjusting values

Idle speed 1/min Idle speed emission value % CO National version

up to 1976 max. 1.5 1) 1976 max. 1.0 without air injection

G ~=1976

GA 1973 up to 1.5 @ 1974 Federal

@s) 1974 California 6–8 without air injection

G@sd) 1975/76 max. 1.0 without air injection

Vacuum governor!)

National version Engine speed Engine speed Vacuum hose pulled off Driving position engaged 1/min 1/min

without with

TN choke TN choke

G@) 1976

G 1976

Gs 1973/74

@) ~—- 1975/76

1) When engaging al! auxiliary units, the engine should still run smoothly.

Special tools

Oil telethermometer – 116 589 27 21 00

Digital tester – 001 589 54 21 00

Connecting cabie 6 m long – 000 589 04 90 00

Intermediate plug (adaptor) – 000 589 72 63 00

Trigger CES Sa 5 – 000 589 71 63 00

oem

Conventional tools

Rpm and CO measuring instrument

Note Do not set idle speed on dynamometer when the engine is too hot, e.g. immediately after a fast drive or after measuring output. The air filter must be mounted.

Adjusting

Adjusting idle speed – rysunek
1 ©Connect test instruments:testerrevolution counter
@ CO measuring instrument @ oil telethermometer 2digital Switch off air conditioning system or automaticor

climate control. Move selector lever into position “P”’.

Adjusting idle speed – rysunek

3 Check whether on vehicles with cruise control (Tempomat) the Bowden wire rests free of tension against regulating lever. Adjust Bowden wire with adjusting nut (1), if required. For this purpose, run engine.

4 Set engine oil temperature to 60—80 °C.

5 Check intake system for leaks. For this purpose, spray all sealed points with Iso-Oktan DIN 51 756 or benzine. A changing engine speed or CO value indicates the presence of leaks.

Attention!

Adjusting idle speed – rysunek
Adjusting idle speed – rysunek

Do not use conventional fuel for spraying (unhealthy vapors). Pay attention to inflammability and do not spray on the red-hot parts or components of the ignition system.

6 With the engine running, check whether throttle valve lever (3) rests against adjusting screw (68).

7 Check idle speed and adjust with adjusting screw (68), if required.

Adjusting idle speed – rysunek

8 Check idle speed emission value without air injection. For this purpose, make air injection inoperative as follows (for @s® 1973/74 nothing need be made inoperative):

@) 1976

Pull off blue/purple vacuum line at connecting point (arrow).

Adjusting idle speed – rysunek

CS) 1976, model 114

Pull rubber cap (arrow) from blue/purple vacuum line.

Adjusting idle speed – rysunek

CG) 1976, model 116

Pull rubber cap (arrow) from blue/purple vacuum line.

Adjusting idle speed – rysunek

@S4 California 1974

Pull off red vacuum line at connecting point (arrow).

Gs) 1975/76

Pull off blue/purple vacuum line at connecting point (arrow).

Adjusting idle speed – rysunek

The exhaust gas for idle speed CO measurement on vehicles with catalyst, (2) 1976 and @sa 1975/76, is drawn off in front of catalyst at check valve (arrow) of air injection.

Adjusting idle speed – rysunek
Adjusting idle speed – rysunek

For measuring idle speed emissions, open valve plate of check valve by means of a self-made wire hook. Connect exhaust gas hose of CO measuring instrument to check valve.

9 Adjust idle speed emission value without air injection. For this purpose, adjust both adjusting screws (arrows) uniformly.

Screwing out = richer

Screwing in = leaner

Adjusting idle speed – rysunek

Accelerate for a short moment, check idle speed and idle speed emission value once again and readjust, if required.

10 Reattach vacuum hose for air injection (air injection operating). The idle speed emission value should now be below the previously set value.

11. Adjust vacuum governor. Run engine, pull off vacuum hose (64), set to specified speed by means of an adjusting screw (63), attach vacuum hose.

Attention! When loosening counternut, apply counterhold to diaphragm rod.

Engage driving position on automatic transmission, set to specified speed by means of adjusting nut (61). Turn power steering to full lock and engage air conditioning system, engine should still run smoothly. Readjust speed, if required.