Cranking engine with s starter

WIS 01-0110

Preceding work: Waming instructions when hood open (01-0085).

A. Model 124

Cranking engine with s starter – rysunek
Cranking engine with s starter – rysunek

Ignition fee eee eee ee we ter ceeeeens switch off. Clamp (arrow) of compression pressure recorder 001 589 77 2100 ………… ween eee clamp onto positive cable of battery. Plug of connector (X27) ww. ee eee ee unplug. Adapter cable (01) 124 589 366300 ……… connect to connector (X27). Adapter cable (1)… wk ee eee eee connect to cable (02) of compression pressure recorder. Engine cc cee cee ee eee sence aes crank by pressing contact handle (arrow) on compression pressure recorder in idle speed position and parking brake applied

Do not crank engine at ignition/starter switch.

antiie RA 01.1214-0110/1

B. Model 129

Cranking engine with s starter – rysunek

Preceding work: Waming instructions when hood open (01-0085).

Ignition 2… eee ce ee eee switch off. Cover (1) over component compartment panel .. remove, install. Plug of connector (X27) 6… eee cece ween unplug. Clamp (A) of compression pressure recorder 001 589 77 21 00 at pin 1 of connector (8) ….. connect. Cover of connector 4/10) …… seen see open, close. Clarnp (B) of cornpression pressure recorder … connect to terminal block (4/10). Engine ……….6. Seen ee eee crank by pressing contact handle (arrow) on compression pressure recorder in idle speed position and parking brake applied.

LN Do not crank engine at ignition/starter switch.

athe §=RA01.1214-0110/2

C. Model 140

Cranking engine with s starter – rysunek

Preceding work: Warning instructions when hood open (01-0085).

013 Pulse counter 0975 Pulse counter adapter X11/4. Data link connector (38-pin)

Cover on left over DI ignition control module …. — take off, fit on. Connector of crankshaft position sensor (L5) AT DI ignition control module (N1/3) 2… 2… pull off, fit on. Engine ………….005 seven see sees crank by means of ignition/starter switch (S2/1). DI ignition control module (N1/3) fault memory .. read (see Diagnosis Manual Engine Volume 2, Index 0).

Note If the engine is started with the crankshaft position sensor (L5) unplugged, a fault is stored in the DI ignition control module (N1/3) fault memory (contact 17, pulse readout 17). This fault must be erased after cornpleting work.

oti = RA 01.1214-0410/3

D. Model 202

Cranking engine with s starter – rysunek
Cranking engine with s starter – rysunek

Preceding work: Warning instructions when hood open (01-0085).

P01-6032–61

Ignition oe ee ee switch off. Cover (1) over connector (X26/25) pull off, fit on. Lacking clamp of connector (X26/25) ……… pull forward with screwdriver. Connector (S) of connector (X26’25) ww. wee unplug, plug in.

whhie RA O1.1214–0110/4

Adapter cable (2)… kee ee eee connect to pin (A1), disconnect. Terminal (A) of compression tester 2… .. see connect to adapter cable (2). Cover at connector (X12/8) oo. ee eee open, close. Terminal (B) of compression tester connect to connector (¢12/3, terminal 30), disconnect. Engine ……… eet e eee nee eee ee vee eee crank by pressing contact switch (arrow) at compression tester, in idle speed position and handbrake applied.

AN Do not crank engine at ignition/starter switch.

Cranking engine with s starter – rysunek

Special tool

athe RA O1.1214-0110/5

E. Model 210

Cranking engine with s starter – rysunek

Preceding work: Warning instructions when hood open (01-0085).

PO1.00-0242–57

Ignition 6… ek eee ee ee sees switch off. Cover (2) over engine cornponent compartment . remove, install. Plug of connector (X22/2) terminal 50 ……… unplug. Adapter cable (01) 124 589 36 6800 ……… connect to connector (X22/2) terminal 50. Cover of connector (X12/8) 2… cee ee open, close. Terminal of compression tester 001 589 77 21 00 clamp to connector (X12/3) terminal 30. Adapter cable (01) …… cee wee eee sees connect to cable of compression tester.

anihiy RA 01.1214-0110/6

ENQiNG eee ee eee crank by pressing contact switch (arrow) at compression tester, in idle speed position and handbrake applied.

LN Do not crank engine at ignition/starter switch.

Cranking engine with s starter – rysunek

Special tool

whe RA OT.1214-0110/7