eae # B11 AR01.45-P-7500C 1

WIS 01-7500C

B11 ARO1.45-P-7500€ Removing, installing oil sump 17.2.95

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

ENGINE 606.961 in MODEL 140 ENGINE 605, 606.912 /962 in MODEL 210

eae # B11 AR01.45-P-7500C 1 – rysunek

P01.45-0246.09

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

# B11 ARO1.45-P-7500C

Shown on model 210 with engine 606.962

eae # B11 AR01.45-P-7500C 1 – rysunek

P01.45-0211–06

Removing, installing

Unbolt ground cabie of battery AR54.10-P-0003A

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

noise 210

atEngine 606.962 in model 210
Model 210 with engine 605.962
Model 140:over fan
Model 210:over fan
Engine 606.962
steering pressurehoseModel 210 Engine 605, 606.912/962 in model 210To enable front suspension support (1) be lowered
front leftEngine 605, 606.912 in model 210
Model 210: outside of frame floor at front left

= # B11 ARO1.45-P-7500C

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

Unbolt front engine mounts (23) at front ful Model 140 suspension support (1) [nr Model 210

Fit on engine supporting frame (01) and Model 140 with engine 606.692 N16 raise engine Detach lines to windshield washer reservoir from fixture at side member and unbolt fixture to enable right front support to be positioned against side member. Fit spacer (05) over threaded bolt of fixture

Spacer for engine supporting arm H18

Model 210 016

eae # B11 AR01.45-P-7500C 1 – rysunek

Ig]

oe Support front suspension carrier A17 inspection pit or assembly lift

B17

45 Oo Detach steering shaft from steering 7 (2)

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

# B11 ARO1.45-P-7500C 7

140 AR33.10-P-0100A

210 AR33.10-P-0100B

606.962

606.962

(iJ Installation: Pay attention to fixture (10) for electric cable of oil level sensor and attachment of ground strap (W11/1) at transmission bell. If automatic transmission fitted (code 420a, 425a) pay attention to bracket for ATF lines (13) and transmission wiring harness (15, 16). i] Pay attention to different lengths and diameters of bolts

Bolt diagram of oil pan ARO1.45-P-7500-06HA @) Align oil pan (24) to rear contact surface on transmission. If the oil pan is not aligned to the transmission, this can result in noise and vibration problems. ka 001 589 76

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

Remove oil pan (24) together with oil pan out oil pan forward in direction gasket (25) rotate crankshaft slightly, if for this step. automatic transmission fitted; press the slightly to the side. contact surfaces of oil pan. oil pan gasket (25).

installation: fix oil pan gasket (25) onto with sealant, if necessary. 210: pay attention to dowel (17)! oil pan is replaced, attach oil level with self-tapping screws.

Install in the reverse order

Inspect oil level of power steering pump, 210 adjust to correct level

Inspect ATF level in automatic transmission, 606.962 adjust to correct level

Inspect engine oil level, adjust to correct level

ae # B11 ARO1.45-P-7500C€

eae # B11 AR01.45-P-7500C 1 – rysunek
Risk of accident as a result of vehicleto prevent it starting off.AS00.00–2-0005-01A
starting off when engine running. Riskand close-fitting work clothes.
injury as a result of bruises and burns ifhot or rotating parts.
insert your hands into engine when it is
being started or when it is running.
Run engine and inspect for leaks

26 Read fault memory, erase. which may be caused by cables or by simulation when removal and installation or to be processed and erased memories after completing the

Volume 1.1: Index 0: using test equipment.

eae # B11 AR01.45-P-7500C 1 – rysunek

Wel Qi) pan

Number Designation

BAO1.45-P-1001-01A Bolt of oil pan to crankcase

BA01.45-P-1002-01A Bolt of transmission bell to oil pan

eae # B11 AR01.45-P-7500C 1 – rysunek

ir Engine suspension, engine mounts, engine supports

Number Engine 604,605, Engine 606.961 in 606 in model 210 model 140

front Nm 35 – BA22.10-P-1061-01D

Nm — 25 BA22.10-P-1008-01D

inj Steering shaft

Model 140 as of vehicle Number Designation ident end no. A-166 260

Bolt of steering joint M8 Nm 20 BA46.10-P-1003-01A

a Steering shaft Model 210 Number

Bolt of steering joint Nm 20

aie #B11 ARO1.45-P-7500C 1

eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek
eae # B11 AR01.45-P-7500C 1 – rysunek

14oss9016100

eae # B11 AR01.45-P-7500C 1 – rysunek

Engine supporting frame Adapter Supports for engine supporting frame Adapter (2 in total)

External torx set ate # B11 ARO1.45-P-7500C 42

Commercially available tools (see Workshop Equipment Manual) NumberDesignationMake (e.g.)Order number
WH58.30-Z-1007-16AEngine oil extractorDeutsche Tecalemit Am Metallwerk 11 33659 Bielefeld1.386950.2
Repair productsOO
NumberDesignationOrder number

,BROO.45-Z-1014-01A Omnifit FD 3041 sealant (50 ml) – 002 989 47 20 10