Programmed Repairs Engines 602.96, 603.96/97 Combustion
WIS Prog_Repairs-comb3
07.1 Diesel Injection System
Complaint:
Engine surges when Idling Engine 603.96 w/o AJC
Remedy Run engine at idling speed. Unplug 2-pin connector (arrow) at servomagnet (Y22). If engine runs properly, check idle speed and set, if necessary, to 580 + 20 rpm. Install modified control module part no. 006 545 36 32 and plug in 2-pin connector again.
Note
Coding bridge of old control module must not be plugged into the new control module. When inserting the new control module, pierce the non-assigned contact 5 in the connector (arrow).
P07-6357–13
Complaint:
Engine does not start when warm or only sluggishly after standing for about 10 minutes
Cause Excessive sheer of petrol in diesel fuel. Not more than 20% regular grade petrol is approved at temperatures below -23 °C; i.e., it is not necessary to add petrol at temperatures higher than -23 °C.
PR 07.1.1064 /1
Complaint:
After parking car on a hill, engine can no longer be started, fuel level < 1/4 full
Cause Injection pump suction chamber runs dry. Internal leak. Vapor bubbles visible at fuel feed. Remedy Check fuel flow filter for leak, replace if necessary. Check connections of top part of filter for leaks and vent drilling for fuel return flow for blockage. Check overflow restrictor at injection pump return. Check injection pump for leak: fuel tank s 1/4 full. Lift up front of car about 40 cm, no vapor bubbles should be visible in the fuel feed pipe, and also not in the fuel return pipe of the injection pump, within 10 min with engine switched off; replace injection pump if necessary.
Complaint:
Engine misfires when cornering sharply, with low Models 124.1/3, 201.1 fuel level = 1/4 full
Cause Fuel pump draws in air. Remedy Install fuel tank with splash pot.
Complaint:
Engine speed increases and blue exhaust after driving sharply
Cause Fluid level in oil sump too high. Remedy Check engine oil level, adjust to correct level if necessary; perform oil change if necessary.
PR 07.1.1064 /2
Complaint:
Engine cannot be switched off or not easily.
Cause/Remedy Vacuum hose and vacuum pump (67) may be split. ® Filter (62) blocked or leaking. ® Restrictor (61b, orange) may be blocked. ® Vacuum of vacuum pump not sufficient. Check vacuum at ancillaries connection. Specification when engine idling after 30 s at least 700 mbar.
P07-6356–55
Complaint:
Engine misfiring evident when slowly accelerating Engines 602, 603 with (up to about 1000 rpm when stationary) AJC
Cause Results from operation of AJC. Remedy Install AJC control module with designation RO2 (was RO1). Part number unchanged. Standard equipment as of end 04/88. No further remedy possible.
PR 07.1.1064 /3
Complaint:
Sharp drop in power (> 10 kW) at full load
Note Engine does not vibrate when idling, no noises evident, compression and pressure loss in order. Fuel filter not blocked. Cause Exhaust or inlet valve spring broken. Remedy Replace valve spring.
Complaint:
Jolts during deceleration when accelerator released Engines 602, 603 with AJC
Cause Deceleration damper has insufficient effect. Remedy Install damper 601 070 13 67. In critical cases the reinforced tension/compression damper 601 070 14 67 can also be installed.
Complaint:
Engine cuts out when clutch released after long motorway trip (200-300 km), or does not idle
Cause Pump governor group jamming briefly (centrifugal elernent in governor of injection pump). Damage code for warranty/goodwill cases: 07 013 15 Remedy Replace injection pump.
PR 07.1.1064 /4
Complaint:
Engine misfires at full load from 2000 rpm Engines 602.96, 603.96
Cause Boost pressure too high or engine overload protection activated too soon. Remedy Test boost pressure with connector unplugged from engine overload protection switch (S66).
If boost pressure 0.95 bar, boost pressure control valve of turbocharger faulty. Replace turbocharger.
If boost pressure <0.95 bar, switch engine overload protection (S66) reacting too soon. P07-6355–13 Replace switch (S66).
Complaint:
Engine has no power (power loss > 20kW) Engines 602.96, 603.96
Cause Rubber connection pipe at hose straps split and as a result the barometric pressure compensation unit is not pressurized with boost pressure. Remedy lf no boost pressure exists at barometric pressure compensation unit, inspect pressure pipes for leaks and replace damaged rubber connection pipes.
Note Do not overtighten hose clips.
PR 07.1.1064 /5
Complaint:
Injection pipes on cylinders 1–4 leaking because of fatigue fracture
Remedy Parts Part no. Install injection pipes with double cone. Ensure the plastic clips are correctly installed.
Complaint:
Engine cannot be switched off when cold (was SI 07.1/37 and 43/6)
Cause Damaged piston vacuum pump (model up to May 1986). Remedy If this problem exists on models manufactured prior to this date, which do not have a second drilling in the oil spray nozzle for the oil supply of the piston vacuum pump, or for performing work which requires taking off the vacuum pump, remove the centering sleeve and install in modified seal for improving the oil supply.
Procedure
1 Remove flange shroud, fan and belt (see Repair Instructions Group 13, Op. No. 342).
2 Remove piston vacuum pump (see Repair Instructions Group 43, Op. No. 618).
3 Remove centering sleeve (3). tt must no longer be installed.
Note The centering sleeve should be installed as an aid when removing the injection pump. It prevents the injection timing device jamming when cranking the engine.
P43-2001–13
PR 07.1.1064 /6
4 Install modified seal (10) in place of the previous one.
5 When dealing with the problem mentioned above, install new vacuum piston pump.
6 Do not connect vacuum pipes to the brake unit at the piston vacuum pump at this stage.
7 Install V-belt, fan and fan shroud.
8 Run engine and pour about 50 cm3 engine oil into the piston vacuum pump through the open vacuum connection with an oil spray can.
P43-2002–13
9 Connect the vacuum pipe to the brake unit Part Part No. immediately. a remamma Refer to the microfiche “operation texts and Piston vacuum pump 000 230 19 65 work units” under Op. No. 43-0610 for the work Seal 601 238 03 80 units.
Production breakpoint of second drilling in oll spray nozzle: May 1986 Model Engine Transmission As of engine end no. 124.133/193 603.960 automatic 000602 126.125 603.961 automatic 002202 124.133 603.962 automatic 000057
Complaint:
Engine misfires between 2000 and 3000 rpm
Cause Overshooting of AJC servomagnet causes quantity reduction. Remedy Install AJC contro! module with the designation RO2 (was RO1), part no. unchanged. Standard equipment as of end 04/88. Adjust AJC control with 2.4 kQ or 4.7 kQ reference resistor (see RAO7.1-1841, pages 13, 14).
PR 07.1.1064 /7
Complaint:
Turbocharger leaking at flange Engines 602.96, 603.96
Remedy Part Part no. Install gasket at turbocharger flange. _—_ CT HC OneO-=OO oO” Gasket (engine 602.96) 602 098 00 80
Gasket (engine 603.96) 252 098 02 08
Complaint:
Loud metallic rattling of 2-mass flywheel after starter not operated Engine 602.96 as of long enough. Engine idles with too low a speed. 09/89 with manual transmission
Cause Idle speed setting at injection pump not correct. Remedy Remove injection pump and set on injection pump test bench. The setting is described in the Bosch microfilm W400/00 under „Reducing idle speed stage of MB cars with EP combination M/RSF Il Engine 602 and TURBO”.
Note Injection pumps as of production date 069 are no longer affected by this problem.
Complaint: Engine 602, 603 up to 30.9.91 with Code 620a EGR valve noisy when opening or closing models with catalytic converter
Remedy Designation Part no. Remove EGR valve, replace, install. In addition I on engines 602.96, 603.96: Vacuum pipe 617 997 08 82 Remove vacuum pipe to EGR valve. Replace, Connection piece 602 078 00 47 install. Remove connection piece between EGR switchover valve and vacuum pipe, replace, install. Damage code: 14 315 36
PR 07.1.1064 /8
Complaint:
Hard combustion noise (clattering) when engine cold and warm
015), and rectify any leaks.
Complaint:
Combustion noise (rumbling) when idling up to about 1300 rpm Engines without exhaust gas recirculation
Set start of delivery to 13° after TDC (GIM method with digital tester). Replacing injection nozzles does not offer any remedy. No further remecy possible.
Complaint:
Combustion nolse accompanied by mechanical noise E Ines 602, 603 9 as Of 1.12.91 at about 1500 rpm
PR 07.1.1064 /9
Complaint:
Engine surges after cold start Engine 603.96 up to 19.10.94
Cause Designation Part no. ESC control module. ESC control module with 007 545 96 32 Remedy software 10/94 and green dot
1 Read fault memory. identification or as of
2 Test ESC (see 07.1-2006), testing, adjusting production date 41/94 – idling speed (see 07.1-2053). automatic transmission.
3 Install ESC control module with software ESC control module with 006 545 36 32 10/94 and green dot identification or as of software 10/94 and green dot production date 41/94. identification or as of production date 41/94 – manual transmission.
Complaint:
EGR pipe split between exhaust manifold and EGR valve Engine 603 up to 18.10.91 with Code 620a models with catalytic converter
Remedy Designation Part no. Replace EGR pipe. EGR pipe 603 142 15 64
Note Install new version of EGR pipe. Damage code: 14 305 06
PR 07.1.1064 /10
Complaint:
Engine has occasional power loss Engine 603.971
Boost air pipe and mixing chamber coked. Fault code output: EDS control module aS _ my CN
– dy: Test vacuum transducer Y31/1 and boost pressure shutoff switchover valve Y31/6 (see RAQ7.1-1120).
Note: When performing test step 5.1 of RA 07.1-1120, 11-14V are measured only if short circuit or fault in boost pressure control circuit, otherwise 0.3 – 0.5V. If no fault can be found, remove boost air pipe and mixing chamber, clean, install.
Complaint:
Jerking durin load changes
Remedy Install tension/compression damper nan (strengthened version). Tension/compression 601 070 14 67 damper
Complaint:
Engine vibrates when idling
not provide any remedy. Remedy
PR 07.1.1064 /11
Complaint:
a) Ei „i load st op not correc stly SOL b) Insufficient full load quantity.
Ren a) Check setting of accelerator control linkage, adjust (see RA30-1010). b) 1 Remove boost air pipe, install (see RA14-1310).
2 Set full load quantity at barometric pressure compensation unit: Take off cap (black) on barometric pressure compensation unit (103). Slacken lock nut (103d). Use a screwdriver to turn setting screw about 1/4 turn to the left. Tighten lock nut (103d). Fit on cap.
Complaint:
Th 18 „boost pressure control is switched off by the EDS control module because of a delay in operation of the switchover valve (Y27/5).
Note After switching off engine or ignition: switching off, on eliminates the problem briefly but does no hot rectify the cause.
Remove switchover valve (Y27/5), replace, install. ode: 54 485 XX delay switch.
PR 07.1.1064 12
Complaint:
Starter has to be cranked for some time before engine starts after Engine 602.96 with being switched off for lengthy time (e.g. overnight), has poor manual transmission in throttle re Model 124, also applies to models with retrofitted Immobilizer
Convert fuel pipes upstream and downstream of check valve (because of installation position).
Complaint:
2ading EDS fault memory although no Engine 602.96 as of 1.6.91 with Code (620a) models with catalytic converter
Ignore fault code.
Note Control modules as of manufacturers date of production 168 in order.
PR 07.1.1064 /13
Complaint:
ed is not reached.
1 Check full load stop, adjust (see RA 07.1-1100).
2 Perform speedometer comparison on roller dynamometer (see RA 07.1-1203).
Note Perform speedometer comparison at about 160 km/h. If the difference is not within tolerance, calibrate speedometer.
3 Test start of delivery (see RA 07.1-8240, RA 07.1-8244).
4 Adjust start of delivery (see RA 07.1-8300).
5 Test max. engine speed at no load (see RA 07.1-1203).
6 Set max. engine speed to top tolerance limit by turning hexagon socket bolt (2m) to the right.
Note 1/2 turn equals 150 rpm.
7 Test full load CO (see RA 07.1-1203). If full load quantity is < 0.1%, increase the full load quantity.
Note On models with the exhaust gas recirculation (Code 620), it is not possible to measure full load CO at the tailpipe. A single adjustment should be performed. If this does not result in any increase in engine output, continue with step 9.
8 Increase full load quantity. a) Engines without anti-jerk control (AJC): Turn slotted screw (2f) about 1/4 turn to the left.
PR 07.1.1064 /14
b) Engines with anti-jerk control (AJC): Remove AJC servomagnet (¥22/3) and flange.
Note Use T30 Torx. Screws are microencapsulated. Slacken lock nut of sliding pin (2y). Turn sliding pin (2y) about 1/4 turn to the left. Tighten lock nut of sliding pin (2y). Bolt on flange and insert servomagnet (Y22/3) without O-ring (162).
Note When inserting servornagnet, no resistance should be felt; shorten lift rod (163) of servomagnet (Y22/3) up to max. 0.3 mm if necessary. Install servomagnet (Y22/3) with O-ring (162). Check injection pump for leaks.
Models with exhaust gas recirculation 9 (Code 620): Remove injection pump, install (see RA 07.1-8410). Set injection pump on injection pump test bench.
PR 07.1.1064 (15
Complaint:
Oil leak and gasket between boost air distribution pipe and cylinder Engines 602.96, 603.96 head
Cause Gasket between boost air distribution pipe and cylinder head.
Remedy Part Part no. Install modified gasket. Notes Gasket (engine 602.96) – 602 141 02 80 05
A slight leakage of oil (sweating) corresponds to Gasket (engine 603.96) the normal condition and is not a problem. Replacing the turbocharger does not offer any remedy. If oil leakage is severe, see AFO1.30-4040AU – 603 141 02 80 05
PR 07.1.1064 /16






















