AR20.00-P-1010HA Checking cooling system for leaks

WIS 20-1010ha

AR20.00-P-1010HAChecking cooling system for leaks
ENGINE 111, 112, 113, 120, 601, 602 /, 603, 604, 605, 606 /, 611}, 120, 601, 602 /, 603, 604, 605, 606 /, 611 /
1 2 = Cooling system cap with detent 2a = 2-stage cooling system cap 3 4Expansion reservoir (Brestcap Tester
P20.00-0397–05
Eg EsRemoving, installing
AR20.00-P-1010HA Checking cooling system for leaks – rysunek

As Danger| Do not open the cooling system unless the AS20.00-Z-0001-01A Risk of injury to skin and eyes from

AR20.00-P-1010HA/3

scalding from hot coolant which splashes coolant temperature is below 90°C. Open out. Risk of poisoning from swallowing cap slowly and allow the pressure to release. Do not pour coolant into coolant. containers for drinks. Wear protective gloves, protective clothes, and eye protection.

Cooling system cap with detent (2): Open cap of expansion reservoir or Carefully turn cap to the first detent, radlator (2, 2a) release pressure, and then unscrew cap

– 2-stage cooling system cap (2a) or cap in model 163: Turn cap half a turn anti-clockwise, release pressure, and then unscrew cap

Set heater switches to maximum heating All except mode! 163 2.1 capacity li} Model 163 has no clocked valves, the coolant flows through the heating system heat exchanger permanently

Testing

Check coolant level, adjust if necessary Engine 111 AH20.00-P-1142-01A

AR20.00-P-1010HA/3

Model! 463, 220, 210, 208, 202, 129 AH20.00-P-1142-01V

AR20.00-P-1010HA/5

with engine 112, 113

Model 163 with engine 112, 113 AH20.00-P-1142-01GH

AR20.00-P-1010HA/7

rest cap for cooling system cap with Install test cap (3) at the expansion reservoir or radiator detent (2) ¥ Test cap for 2-position cooling system cap – 210 589 00 91 00

[7] Test cap for model 163 with engine 112, 113 – 163 589 01 91 00

5 Connect tester ig] 124 589 24 21 00

6 Test cooling system for leaks Test pressure approx. 1.4 bar. @) If cylinder head gaskets are new, first of all bring engine to operating temperature and then test cooling system for leaks

7 Inspect cooling and heating hoses and also their connection points for proper condition and loss of coolant, reptace coolant hoses if necessary

8 Inspect condition and installation of hose WHS58.30-2-1001-06A clips, retighten or replace if necessary

AR20.00-P-1010HA Checking cooling system for leaks – rysunek
AR20.00-P-1010HA Checking cooling system for leaks – rysunek
AR20.00-P-1010HA Checking cooling system for leaks – rysunek

WH58.30-Z-1002-06A

\_ 124589009100 \ 163589019100 =f \ 210589009100) Tester Test cap Test cap Test cap

Commercially available tools

Number Designation Make (e.g.) Order number

WHS58.30–2-1001-06A 6 mm wrench hexagon on flexible shaft for hose clips with worm Hazet 426–6 drive Guldenwerther BahnhofstraBe 25–28 D-42857 Remscheid

WHS58.30-Z-1002-064 7 mm wrench hexagon on flexible shaft for hose clips with worm Hazet 426–7 drive GUldenwerther BahnhofstraBe 25–28 D-42857 Remscheid

AS20.00–2-0001-01ARisk of injury to skin and eyes fromDo not open the cooling system unless A Danger!
scalding from hot coolant which splashesthe coolant temperature is below 90
out..Risk of poisoning from swallowing°C. Open cap slowly and allow the
coolant.pressure to release.
Do not pour coojant into containers
for drinks.
Wear protcctive gloves, protective
clothes, and eye protection.

Possible dangers Protective measures/rules of conduct – Allow cooling system to cool down to a coolant temperature Risk of injury of less than 90 °C. The cooling system is pressurized when the engine is warm. Risk

– Open coolant system cap slowly; open a conventional type of

of scalding from hot coolant which splashes out if the cooling coolant system cap to the first detent and open a screw-type system is opened suddenly. coolant system cap about 1/2 turn, and allow the pressure to release. – Wear protective gloves, protective clothes, and eye protection. Risk of poisoning If coolant is swallowed, the person affected is likely to show signs – Donot pour coolant into containers for drinks. of poisoning such as headaches, giddiness and stomach aches, paralysis of the respiratory system, unconsciousness, nausea, and First aid measures e@ Pour large quantities of cold water over the affected area of convulsions. skin and cover over with sterile bandages. @ Have person affected drink plenty of water to which medicinal! carbon has been added. e@ Consult a doctor if the person affected has severe burns or has swallowed considerable quantities.

AR20.00-P-1010HA Checking cooling system for leaks – rysunek

Model 124, 129, 140, 168, 170, 202, i AH20.00-P-1142-01A Notes on engine coolant Jeve! 208, 210, 463

AR20.00-P-1010HA Checking cooling system for leaks – rysunek

Mode! 124: The coolant level when the engine is cold must extend up to the marking (arrow) on the coolant expansion tank. When coolant is warm; about 1 cm above this marking.

Model 129: The coolant level when the engine is cold must extend up to the marking (arrow) on the coolant expansion tank. When coolant is warm: about 1 cm above this marking.