Checking, adjusting basic setting of camshafts

WIS 05-2230

Checking, adjusting basic setting of camshafts – rysunek

Preceding work: Cylinder head covers removed (01-0500)

Checking rotate to 45° before ignition TDG with socket EMQin@ 6… ee eee ee eee eee eee eee wrench, special tool 001 589 65 09 00 (step 1). It rust be possible to pin the camshafts with the pins (1) ……4.. vee sete eee see wae special tool 111 589 03 15 00 (step 2).

waka RA 05.1323-2230/1

Adjusting (at 45° before TDC) Guide rails (2) 2… ee seen e ene rernove, install (05-3350). Chain tensioner ….. stews seen eens ramove, install (05-3100). Camshafts, beginning at right exhaust camshaft. rotate with wrench in direction of rotation of engine, special tool 111 589 01 01 00 (step 5). samshafts, beginning at left exhaust camshaft . . rotate into position with wrench, special tool 111 589 03 15 00 (step 6). Timing chain 00a ee see seen fit on. Camshafts 6.0… cee ee eee sence ene pin with pins (1), beginning at left exhaust camshaft, special tool 111 589 03 15 00 (steps § to 9).

Checking, adjusting basic setting of camshafts – rysunek
Checking, adjusting basic setting of camshafts – rysunek

Special tools

Note The 45° before TDC marking on the vibration damper is an assernbly marking. The camshafts can be rotated in this position with the wrench 119 589 00 01 00 without the valves coming into contact with the piston.

wihin RA 05.1323-2230/2

Checking, adjusting basic setting of camshafts – rysunek

1 Position engine to 45° before ignition TDC at No. 1 cylinder by cranking engine at crankshaft in direction of rotation of engine using special tool 001 589 65 09 00.

Checking, adjusting basic setting of camshafts – rysunek

2 It must be possible to pin all 4 camshafts with the pins (1), special tool 111 589 03 15 00, through the 6.5 mm dia. holes in the first camshaft bearing caps.

Checking, adjusting basic setting of camshafts – rysunek

Adjusting (at 45° before TDC)

3 Remove, install top slide rail (2a) (05-3350). a

4 Remove, install chain tensioner (05-3100).

Checking, adjusting basic setting of camshafts – rysunek

5 Rotate camshafts in direction of rotation of engine with wrench, special tool 119 589 00 01 00, beginning at right exhaust camshaft (1). To make it possible to start the adjustment at the left-hand exhaust camshaft (4), the slack section (arrows) of the timing chain (at chain tensioner) must be transferred by rotating the carnshafts (1, 2, and 3).

Engine 119.960

othe RA 05.1323-2230/3

Checking, adjusting basic setting of camshafts – rysunek
Checking, adjusting basic setting of camshafts – rysunek

position with wrench (3) 119 589 00 01 00. Fit timing chain onto exhaust carnshaft timing gear and pin with pin (4) 111 589 03 15 00,

7 Rotate left-hand inlet camshaft into position with wrench (3). Fit timing chain onto inlet . camshaft timing gear and pin with pin (1). Camshafts in retarded” position (arrow).

8 Rotate right-hand inlet camshaft into position with wrench 119 689 00 O01 60. Fit timing chain onto inlet carnshaft timing gear and pin with pin 111 589 03 15 00. Camshafts in „retarded” position (arrow).

9 Rotate right-hand exhaust camshaft into position with wrench 119 589 00 01 00. Fit timing chain onto exhaust camshaft timing gear and pin with pin 111 589 03 15 00.

installation is performed in the reverse order, beginning from step 4.

uti RA, 05.1923-2230/4