Testing and adjusting ignition timing (breakerless transistorized ignition system)

WIS 15-501

Testing and adjusting data

Testing and adjusting ignition timing (breakerless transistorized ignition system) – rysunek

A. Standard version

Adjusting value!) — Test value ignition) Test value ignition Vacuum adjustment Installation value
firing pointtiming
vacuumwith/without vacuum
3000/minidle with ~1500/minwithout3000/min
–~
Toc+3° 515–19° 630 5
Toc+s14–22°30°
Testing and adjusting ignition timing (breakerless transistorized ignition system) – rysunek

1) 1 normally compressed engines are operating with fuel under 98 RON (min. 88 MON) adjust firing point in direction of “retard’’ and match to octane rating of fuel used. A reference value for this adjustment is: Set firing point back by 1–2° crank angle per 1 RON. Max. setback should not exceed 6° crank angle.

Attention! Taking firing point back is considered an ‘emergency measure’. Reduced input and increased fuel consumption will result. In addition, the engine cannot be fully loaded. As soon as fuel with specified octane number is available, set engine to full advance. 2) For ignition timing, pull off both vacuum lines for ignition adjustment. Switch off air conditioning system, automatic transmission in position ‘‘N” or “P”.

B. National version @s) G) Cs) Gs) l Engine Ignition Adjusting value of Test value Vacuum adjustment Installation value distributor firing point ignition timing after of ignition Bosch no. with vacuum without vacuum “retard” ‘’advance’’ distributor at starting speed at at 3000/min at idle 1500/min 3500/min idle without vacuum

1977 Identification: Silver information plate on cross member in front of radiator

117 0 237 405 001 ToC 9–16° 27–33° 6–10° 8–12° 7° BTDC

starting 1978

117 0 237 405 002 TDC 9–17° 26–34° 610° 812° 8° BTDC

1980

117 0 237 405 008 TOC 9–17° 26–34° 6–10° 8–12° 8° BTDC

e® starting 1976 Identification: Information plate on cross member in front of radiator in Japanese language

W17 0 237 405 001 TDC 9~16° 27–33° 6–10° 8–12° 7° BTDC

G) 1980 Identification: Information plate on cross member in front of radiator in Japanese language

117 0 237 405 006 ToC 9–16° 27–33 ° 6—-10° 8–12° 7° BTDC

G) 1976/77 Identification: Blue information plate in Swedish language on cross member in front of radiator

17 0 237 405 001 TDC 9~16° 27-33° 6—10° 8—12° 7° BTDC

Cs) 1978/79

117 0 237 405 002 TOC 9~16° 27–33° 6–10° 8–12° 8° BTDC

Cs) 1980

117 0 237 405 008 TDC 9~16° 27~33° 6–10° 8–12° 8° BTDC

1976/77 Information plate in English language on cross member in front of radiator Identification: 1976 black or green 1977 Federal black, California yellow, Federal high altitudes red

117 0 237 405 002 TDC 9–16° 27–33° 6–10° 812° 7° BTOC

USA) 1978/79 Identification: Federal black, California yellow TT 1 117 0 237 405 002 TDC 9~16° 27–33 ° 6–10° 8–12° 7° BTDC

1980 Identification: Black information plate in English language on cross member in front of radiator

0 237 405011 ° 1 ° ° ° ° ° 117 0237 405 0122) 5° BTDC) 7–13 22–28 9–11 8–12 5° BTOC

1) Adjustment at operating temperature of engine. Vacuum retard adjustment is switched off above 50 °C engine temperature. 2) Starting February 1980.

Conventional tools

Revolution counter (speedometer), stroboscope

Digital tester Bosch, MOT 001.03

Checking and adjusting

Testing and adjusting ignition timing (breakerless transistorized ignition system) – rysunek

Note: On standard version, pull off both vacuum lines for ignition adjustment when adjusting firing point. After adjusting firing point, check specified firing point at idle with vacuum.

1 Check firing point with stroboscope or digital tester at specified speed with or without vacuum.

2 Loosen ignition distributor attachment, if applicable, and set adjusting value of firing point by turning ignition distributor.

Screw down ignition distributor and check firing point once again.

3 Check centrifugal and vacuum adjustment of ignition distributor. For this purpose, run through specified test values with or without vacuum adjustment.