Adjusting regulating linkage

WIS 30-300

A. Model 115

Length of regulating rod in mm’)

without air conditioning 263 Manual transmission —_ with air conditioning 238

Automatic transmission 251

1) Adjusting dimension, measured from center of bal! socket to center of ball socket.

Prior to adjusting regulating rod and contro! pressure rod make sure that the automatic choke is switched off and that the idle speed stop is at carburetor. The Bowden wire for cruise control/Tempomat should rest free of tension against regulating lever.

Adjustment

Regulating linkage on manual transmission

Adjusting regulating linkage – rysunek

Adjust regulating rod (1) in such a manner that roller (3) in slotted lever (2) rests free of tension against end stop.

On vehicles with air conditioning, keep engine running for this purpose.

Note: The regulating rod has lefthand and righthand threads.

Length without air conditioning 263 mm Length with air conditioning 238 mm

Regulating linkage with automatic transmission

Adjusting regulating linkage – rysunek

With engine running, adjust regulating rod on ball socket (arrow) in completely extended condition to permit connection to throttle valve lever free of tension.

Adjusting regulating linkage – rysunek

Adjusting control pressure rod

Adjusting regulating linkage – rysunek

Run engine at idle. Disconnect control pressure rod (7) by pulling off ball socket (5) and push to the rear up to stog (idle throttle position). In this position, adjust ball socket (5) in such a manner that the control pressure rod can be connected free of tension.

California version

Unscrew vacuum governor, disconnect connecting rod to automatic choke in such a manner that the throttle valve rests against idle speed stop.

Loosen clamping screw (3), turn the two levers 2 and 4 inrelation to each other until the control pressure rod rests completely at the rear against idle speed stop.

Tighten clamping screw (3), then kickdown from accelerator lever end and check whether throttle valve rests against full throttle stop, adjust full throttle stop, if required.

Adjusting regulating linkage – rysunek

Screw vacuum governor on again and reconnect connecting rod to choke.

Adjusting full throttle stop

On vehicles with manual transmission step completely down on accelerator pedal with engine stopped. In this position, the throttle valve lever should rest against full load stop (arrow) of carburetor.

Adjusting regulating linkage – rysunek

On vehicles with automatic transmission depress accelerator pedal, with engine stopped, only up to stop on kickdown switch (do not operate kickdown switch). In this position, the throttle valve lever should rest against full throttle stop (arrow) of carburetor.

If full throttle stop is not attained, loosen clamping screw (arrow) on regulating shaft. Release accelerator pedal slightly and tighten screw again. Check full throttle stop once again, and repeat adjusting procedure, if required.

Adjusting regulating linkage – rysunek

California version

Adjusting regulating linkage – rysunek

With accelerator pedal completely down, set adjusting screw (116) in such a manner that a clearance of 0.5 mm is available between throttle valve lever and stop (arrow) on carburetor housing.

B. Model 123

Length of regulating rod in mm’)

without air conditioning259
with air conditioning232

Automatic transmission 247

Note Prior to adjusting regulating rod and control pressure rod make sure that the automatic choke is switched off and that the idle speed stop is at carburetor. The Bowden wire for cruise control/Tempomat should rest free of tension against regulating lever.

Adjusting regulating linkage – rysunek

Adjustment

Regulating linkage with manual transmission

Adjust regulating rod to permit connection free of tension. If required, loosen clamping screw (1 or arrow) and adjust length accordingly.

On vehicles with air conditioning, run engine for this

Adjusting regulating linkage – rysunek

purpose.

Regulating linkage with automatic transmission

Adjusting regulating linkage – rysunek

With engine running, set regulating rod in such a manner that rod can be connected free of tension in completely extended condition (arrows). Adjust length of control pressure rod by means of ball socket (5) as required.

Adjusting regulating linkage – rysunek

Adjusting control pressure rod

Run engine at idle. Disconnect control pressure rod (7) by pulling off ball socket (5) and push to the rear up to stop (idle speed position). In this position, adjust ball socket (5) in such a manner that the control pressure rod can be connected free of tension.

Adjusting full throttle stop

Adjusting regulating linkage – rysunek

On vehicles with manual transmission step completely down on accelerator pedal with engine stopped. In this position, the throttle valve lever should rest against full load stop (arrow) of carburetor.

On vehicles with automatic transmission depress accelerator pedal, with engine stopped, only up to stop on kickdown switch (do not operate kickdown switch). In this position, the throttle valve lever should rest against full throttle stop (arrow) of carburetor.

Adjusting regulating linkage – rysunek

If full throttle stop is not attained, loosen clamping screw (arrow) on regulating shaft. Release accelerator pedal slightly and tighten screw again. Check full throttle stop once again, and repeat adjusting procedure, if required.

Righthand steering vehicles

Adjusting regulating linkage – rysunek

With engine stopped, step down on accelerator pedal fully on vehicles with manual transmission, and up to

stop on kickdown switch on vehicles with automatic

transmission (do not operate kickdown switch).

The throttle valve lever should now rest fully against full throttle stop of carburetor.

Adjusting regulating linkage – rysunek

If full throttle stop is not attained, readjust Bowden wire (12) with adjusting nut (13) until throttle valve lever rests against full throttle stop.