Grinding camshaft bearing journals
WIS 05-225
Data
| Mean roughness of camshaft bearing journal | 0.005 | ||||||
| Deviation of camshaft bearing journal from true when mounted at camshaft sprocket seat and rear camshaft bearing journal | 0.030 | ||||||
| Deviation of camshaft bearing journal from true | 0.010 | ||||||
| Bearing points (fig., refer to note) | 1,9 | 2 | 3,10,11 | 4,5,12,13 | 6,7,14,15 | 8 | |
| Standard dimension | bearing dia. | 38.016 38.000 | 50.066 50.050 | 50.016 50.000 | 51.519 51.500 | 53.019 53.000 | 54.019 54.000 |
| journal dia. | 23.993 23.980 | 49.950 49.934 | 49.950 49.934 | 51.440 51.421 | 52.940 52.921 | 53.940 53.921 | |
| Intermediate stage | bearing 9 dia. | 49.966 49.950 | 49.916 49.900 | 51.419 51.400 | 52.919 52.900 | 53.919 53.900 | |
| —0.1 mm (exchange engines) | journal dia. | 49.850 49.834 | 49.850 49.834 | 51.340 51.321 | 52.840 52.821 | 53.840 53.821 | |
| 1st repair stage | bearing dia. | 49.816 49.800 | 49.765 49.750 | 51.269 51.250 | 52.769 52.750 | 53.769 53.750 | |
| —0.25 mm | journal dia. | 49.700 49.684 | 49.700 49.684 | 51.190 51.171 | 52.690 52.671 | 53.690 53.671 | |
| 2nd repair stage | bearing dia. | 49.566 49.550 | 49.516 49.500 | 51.019 51.000 | 52.519 52.500 | 53.519 53.500 | |
| —0.5 mm | journal dia. | 49.450 49.434 | 49.450 49.434 | 50.940 50.921 | 52.440 52.421 | 53.440 53.421 | |
| Camshaft bearing | radial | 0.057 0.124 | 0.100 0.132 | 0.050 0.082 | 0.060 0.098 | 0.060 0.098 | 0.060 0.098 |
| play | axial | 0.050 0.120 | |||||
37.950 jp 24.013 Sleeve for bearing a OD 37.925 24.000
Special tool
Dial gauge holder for camshaft axial play – 136 589 04 21 00
N 8
Note For camshafts with reground bearing journals, cam-
shaft housings with repair stages —0.25 mm and
—0.50 mm are available.
The bearing journals are not hardened.
9 10 12
Some exchange engines are delivered with camshaft bearings in intermediate and repair sizes. This means that a standard camshaft cannot be installed in this camshaft housing, since the bearing journals are larger in diameter than the bearings.
Also refer to coordination camshaft housing and camshafts (01–471).
Chamfer bearing journals after grinding (see sketch for dimensions).
0,5×45°
Checking axial play
1 Bolt dial gauge holder to camshaft housing.
2 Clamp dial gauge with a preload of about 3 mm.
3 Press back camshaft and set needle at 0.
4 Press camshaft forward and read axial play.
Note: If the end play is too small, grind spacing sleeve or driver at face B as required.
If the axial play is too large, the spacer or dog must be ground at collar A.
Camshafts
1 2 expansion bolts 2nd version Ono Spacer 1a 2 bolts 1st version (not valid) 2 camshaft sprockets 2 2 washers 2nd version 2 woodruff keys 4 x 6.5 2a 4 washers 1st version (not valid) Exhaust camshaft
3 2spacers Intake camshaft




