Programmed Repairs Engine 104 Combustion CIS-E Injection

WIS Prog_Repairs-comb-cise

Note Engine speed characteristics The specific engine speed characteristics are described below in order to facilitate fault diagnosis.

1. Engine speed „After starting” Since September 1989 KAT vehicles run at a fast idling speed (1000 ~ 1200 rpm) for up to max, 1 minute after starting or up to a coolant temperature of 30 °C. This “heating speed” enables the catalytic converter to reach its operating temperature faster.

Engine speed „Vehicle moving” Engines with CIS-E control units to which the road speed signal is supplied have an idling speed which is 50 -— 200 rpm higher when the vehicle is moving.

3. Engine speed „In deceleration mode” Deceleration fuel cutoff is activated as soon as the driver’s foot is released frorn the accelerator.

Note Only on vehicles with automatic transmission, engine speed increases briefly by 100 ~ 300 rpm when combustion is restored in the deceleration mode. The vehicle speed does not increase as a result of this, however.

Complaint:

Engine mistires above 4000 rpm in position „D”, vibrates (only vehicles with automatic transmission.

Test transmission overload protection (see Diagnosis Manual Engine, Volurne 2, Index 5.1, Test step 8.0 9.2, and also Volume 4, Wiring Diagrarns).

gihia §=RA 07.3 1212/1 PR

Programmed Repairs Engine 104 Combustion CIS-E Injection – rysunek

1. Return spring wrongly laver. 2. Throttle valve idle speed not operated.

1. Attach return spring correctly lever (see Fig.) 2. Test idle speed contact at switch (see Diagnosis Volume 2, Index 2).

Complaint:

Engine cuts out when air conditioner operating in deceleration mode when clutch is depressed, but can be started again immediately

Replace SIS-E control unit. The control units have been modified as from production date 172 (December 91).

Complaint:

Poor throttle response, occasional misfiring, poor idling, engine backfires into intake manifold

Distributor finger sparks over or has cracks.

Rermed\

ania RA 07.3 1212/2 a

Complaint:

Programmed Repairs Engine 104 Combustion CIS-E Injection – rysunek

ine difficult to start (long starting time)

Complaint:

Engine does not fire on all cylinders (rough)

1. Injection valves leaking. 2. Zero position of air flow sensor plate not in order, fuel distributor.

1. Check injection valves, replace if necessary. 2. Check zero position of air flow sensor plate (see 07.3-1612). Unbolt all the fuel injection lines at the injection valves and at the fuel distributor. Remove fuel pump relay and bridge two terminals 30 and 87. When the air flow sensor plate is in the zero position, no fuel must flow out at the pressure outlets; test fuel distributor and replace, if necessary. When the air flow sensor plate is deflected, fuel must flow out simultaneously at all the pressure outlets of the fuel distributor; replace fuel distributor if necessary.

wri = RA 07.3 1212/3 PR

Complaint:

Engine cuts out suddenly and starts again after a short time

/Rermedy As it is very difficult to determine the cause of this complaint, perform the following checks: ® Gheck the connections at the ignition coil. : ® Test cable terminal TD for occasional short to ground, e. g. at diagnostic socket, at tachometer, at connection of fuel pump/AC compressor cutoff relay. ® Check the contacts of the connectors of the fuel pump relay, overvoltage protection with a gauge {e. g. individual pin of plug); press together widened contacts. Check the connectors of the fuel pump/AC compressor cutoff relay for signs of moisture and corrosion. Clean connector if necessary and replace relay. ® Chack position sensor for open circuit by moving the cable at the sensor or at the plug connection; replace if necessary.

Complaint:

Engine cuts out when driving, can no longer be started

Cause Cable of oxygen sensor occasionally touching propeller shaft resulting in short to ground. Conductor path in fuel pump relay burnt through.

Replace oxygen sensor. Ensure that the cable is correctly rooted. Replace fuel pump relay.

«mine §=RA 07.3 1212/4 PR

Complaint:

Engine cuts out when decelerating

1. Electrohydraulic actuator. 2. No road speed signal from speedometer to CIS-E control unit.

1edy Test electrohydraulic actuator, replace if necessary. 2. Connect multimeter to connector of CIS-E control unit, contact 29 and ground. Switch on ignition. Move car forward and back. Specification 0 – 12 V without electrical components, 0 ~ 9 V with electrical components such as cruise control, temperature display. Check whether Hall sender on rear of speedometer is installed. Check cable routing frorn Hall sender to connector (X26), contact 11. Test plug connection (53/5) (loose contact), install Hall sender if necessary, Part No. 007 542 29 17 as of production date 06/88. Check cable routing from Hall sender to fuse 5, ©. g. cable shoe not connected at fuse 5.

Manual transmission model 124

Remedy (only vehicles up to end 04/90) Detach cable from pin 28 CIS-E control unit connector to plug connection (X26) pin 10, at plug connection (426) and connect to ground. On vehicles as of 05/90 the cable from the CIS-E control unit to plug connection (X26) is no longer fitted.

an Use ohmmeter to check that the cable to the CIS-E control unit pin 28 is connected to ground and not the cable to the ignition starter switch (S2/1) otherwise this will result in a short circuit.

complaint:

jine sometimes does not start, or cuts out

Cause Position sensor for activating the ignition system has occasionally open circuit or short circuit to ground.

t position sensor, replace if necessary (see 15-2133 or Diagnosis Manual Engine, Volume 2).

aihin = RA 07.3 1212/5 PR

Complaint:

Poor hot starting

Check part no. of fuel accumulator, correct part no. is 000 476 09 21 or 10 21. If part no. is not correct, replace fuel accumulator and fuel pipe 129 470 05 64.

complaint:

Vehicle occasionally vibrates between 140 km/h and 160 km/h (only brief misfiring for about 0.3 $)

= control unit. Only on vehicles with the vehicle ident end no. as listed below: 124.031 1B 473 729 124.051 1B 469 543 124.091 1F 180 767 129.061 1F 032 455

Cornplaint:

Poor output (engine at operating temperature)

Cause ———— nnn EE = . . co, . . Resistance trimming coupling Resistance EZL/AKR resistance trimming coupling, possibly Part No. ohms wrong resistor installed. serrrennrerennenerneenernnennen nena 015 545 67 28 (with KAT) 2400 Remedy 015 545 68 28 (G5) version) 1300 0 sK istance: FEZ q ‘Sis iC : -y + Check resistances of EZL/AKR resistance 015 545 70 28 (without KAT) 470 trimming coupling from table; if difference exists, mmm replace resistance trimming coupling.

atin §=RA 07.3 1212/6 PR

Complaint:

Occasionally poor output when starting off and at outside temperatures > +30 °C

Ignition control unit, sharp retardation of ignition at outside temperatures > +30 °C. Only vehicles affected up to vehicle ident end no. listed below: 124.031 1B 473 729 124.051 1B 469 543 124.091 1F 180 767 129.061 1F 032 455

Complaint:

Programmed Repairs Engine 104 Combustion CIS-E Injection – rysunek

Poor output when starting off at altitudes above 2000Imeters

104.981 010 545 95 32 Remedy ——_— = Replace Bosch EZL/AKR ignition control unit with Part No. 010 545 39 32 up to production date 946. Read fault memory in CIS-E control unit and erase, if necessary.

Engine running complaints In particular sporadic cutting out of engine may be caused by different factors. The following test catalog enables faults in the different operating states to be specifically detected and rectified. The operating state in which the engine cuts out is particularly important for determining the remedial measure to be taken.

The test steps should be conducted in the order stated.

Perform the tests as specified in the Diagnosis Manual betore working with the test catalog.

anthiin = RA 07.3 1212/7 PR

A. Engine cuts out when idling: 1. Contacts at connector of air flow sensor position indicator widened. Press contacts together, replace socket Part No. 003 545 26 26.

2 If knocking lightly on overvoltage protection causes engine to cut out or misfire, replace overvoltage protection.

Check whether 4 mm contact of cable to crankshaft position sensor is widened, press together if necessary.

Programmed Repairs Engine 104 Combustion CIS-E Injection – rysunek

Idle speed adjuster modified as of production date 951; up to 950 test internal resistance.

suspension dome loose or corroded. Unbolt cable, clean and bolt on.

No road speed signal at CIS-E control unit, pin 29. For remedy see Diagnosis Manual Engine, Volume 2.

if battery voltage exists at pin 28 of CIS-E control unit when starting (only model 124 with manual transmission), separate plug connection (X26) violet cable and connect to ground.

idle speed contact or deceleration fuel cutoff 4, microswitch occasionally not closed in idle speed position. Adjust throttle control.

Contacts of terminals 15, 30, 31 or 87 at 5. overvoltage protection widened. Press together contacts.

Check whether 4 mm contact of cable to crankshaft position sensor is widened, press together if necessary.

Move cable of crankshaft position sensor to EZL ignition control unit. If engine cuts out when this is done, replace position sensor.

Test electrohydraulic actuator, replace if necessary.

agmkta = RA 07.3 1212/8 PR

Cc. Engine j. Ground cable at fuel pump loose. Attach speed: ground cable properly.

2. Cables of terminals 1 and 15 at ignition coil loose. Tighten cables.

3. Move cable from crankshaft position sensor to EZL ignition control unit. If engine cuts out when this is done, replace position sensor.

4. Check whether 4 mm contact of cable to crankshaft position sensor is widened, press together if necessary.

§. Test EZL ignition control unit, replace if necessary.

D. engine cuts out when accelerating: 1. Ground cable at fuel pump loose. Attach ground cable properly.

2. Contacts of terminals 15, 30, 31 or 87 at overvoltage protection relay widened. Press together contacts.

3. Gables of terminals 1 and 15 at ignition coil loose. Tighten cables.

4. Move cable from crankshaft position sensor to EZL ignition control unit. If engine cuts out when this is done, replace position sensor.

5. Check whether 4 mrn contact of cable to crankshaft position sensor is widened. Press together if necessary.

6. Test EZL ignition control unit, replace if

Complaint:

Combustion noises (except Gs)

Since April 1991 an EZL ignition contro! unit with a modified ignition map and a modified CIS-E control unit for the adjustment range of the inlet camshaft have been installed as part of further engineering developments with the aim of reducing combustion noises (see Notes 15-2093 and 07.3-1698). Replace EZ! ignition control unit and CIS-E control unit. The CIS-E contro! unit must be installed only with the relevant EZL. ignition contro! unit.

swthye §=RA 07.3 1212/9 PR

Complaint:

Fuel pump loud

Programmed Repairs Engine 104 Combustion CIS-E Injection – rysunek

In dealing with the complaint „Fuel pump loud” it is important to distinguish between whether a buzzing sound or a clinking noise is heard.

of kinks. distributor is fouled (high backpressure increases noise level). 3. Install Knecht fuel filter (if not already fitted). 4. Replace fuel pump. As of production date 642 with shaped track.

1. Replace fuel pump (worn). 2. It this does not bring about a remedy, check drainplug and filter in fuel tank for signs of fouling.

Complaint:

Determining faulty input signals in CIS-E control unit

Use Lambda tester to determine faulty input signals by measuring On/Off ratio. Then, perform test program (see Diagnosis Manual Engine, Volume 2).

othin =RA 07.3 1212/10 PR

Complaint:

On/Off ratio cannot be set Sudden increase in fuel consumption (about 2 – 3 liters)

Note There must not be any leaks in the exhaust systern.

Cause 1. Occasional or constant failure of oxygen sensor when driving. 2. Screened cable from oxygen sensor connector (G3/2×2) to control unit pin 8 has short to ground. 3.Loose contact or occasional open circuit at connectro sleeve Z (soldered connector in wiring harness from coupling of CIS-E control unit).

Remedy 1. Test Lambda control when engine idling (see Repair Instructions Engine Combustion, or Diagnosis Manual Engine) and on the dynamometer in upper load range or when driving (readout must fluctuate). If the readout on the Lambda control tester moves slowly against the stop on the right in the closed-loop mode, the oxygen sensor must be replaced. 2. Separate plug connection (G3/2×2) for oxygen sensor signal and also unplug coupling at CIS-E control unit and measure resistance of contact 7 to contact 8. Specification: «© Q 10 kQ) If continuity exists (<1 2), replace engine wiring harness. 3. Open coupling of CIS-E contro! unit (N3) and re-solder connector sleeve Z (soldered connector i 5 harness) at contact 7 (cold solder point).

aime =RA 07.39 1212/11 PR

Cornplaint:

Diagnosis with fault storage (pulse readout at CIS-E control unit, engine systems control unit E2L/AKR ignition control unit)

Cause/Remed:

The pulse readouts stated in the table are stored faults although no faults are present in the systems. They should therefore be ignored.

AN The engine must be conditioned first of all in order to raad the fault mernory of the EZL/AKR control unit. See Diagnosis Manual Engine, Volume 2, Engines 104, 119 CIS-E in the column „Pulse readout”.

CIS-E control unit Engine systems control unjt (MAS) ’) EZL/AKR ignition control (pulse readout) {pulse readout) unit (pulse readout) 104 22%) 2und 3 14%)

8 1) MAS can be diagnosed as of standard installation calendar week 27/89, in order as of part no. Engine Part no. w/o AG compressor Part no. with AC compressor 104 O11 545 82 32 011 545 83 32 119 011 545 84 32 011 545 85 32 2) Only with engine systems control unit 007 545 59 32 and 007 545 60 32 and only with version “without KAT”. 3) Bosch ignition control unit 007 545 70 32 in order as of production 946, Siemens ignition control unit 007 545 71 32 as of production date 27/89.

wie RA 07.3 1212/12 PA

Complaint:

Programmed Repairs Engine 104 Combustion CIS-E Injection – rysunek

ASR indicator lamp lights up when driving and electronic accelerator pedal moves into emergency running mode (difficult to depress after short idle travel)

1. Check production date of control unit (see Fig.) Control units with production dates from 16/88 up to 43/88 must be replaced with a control unit as of production date 44/88 (identification: yellow dot) if this fault occurs.

2. Check throttle control linkage, adjust . .

(see 30-1010, Section „B”).

3. Replace potentiometer (R25).

Complaint:

Engine misfires around reserve fuel quantity and when cornering

Cause/Remedy Madel 124 Sedan, Coupé. ‘Install new fuel tank.

wth §=RA 07.3 1212/13 PR

Complaint:

Klicking noises. Fuel leaking (smell of fuel), compressed. Only with fuel evaporation system

Insufficient ventilation of fuel tank through fuel evaporation system.

ist Cause Poor routing of hoses in left front wheelhouse (kinked, crimped).

Remed\ Remove bulkhead at left front wheelhouse. Check visibly and also whether hoses blocked (not with compressed air). Rectify fault.

2nd Cause

Blow through 10 mm @ connection to 8 mm @ connection at activated charcoal filter (not with compressed air). At the same time hold 6 mm @ connection closed.Compare with new activated charcoal filter, if necessary. If insufficient clear passage, replace activated charcoal filter.

Note Because of the twin-shell design of the front muffler and the high temperatures, stresses are produced when the muffler cools down which results in this noise. A further cause is the high level of heat radiated from the front muffler to the shield.

Remedy A remedy is not possible on the basis of current state of engineering. The fault has no effect on the life of the exhaust system.

tha §=RA 07.3 1212/14 PR

Complaint:

Catalytic converter makes noises, monolith in KAT loose

Complaint:

Front passenger footwell heats up because of catalytic converter

1. Check clearance of heatshield (above catalytic converter) to underfloor of car. Specification: 8 ~ 10 mm; adjust clearance if necessary.

2. Lay glass fiber matting, Part No. 000 989 18 10 below footmat (only available in square meter sizes).

Note Model 124 RUF/KAT: Glass fiber matting in front passenger footwell fitted as standard since 07/88. Production breakpoint as of vehicle ident end no. A 798379 B 082239

Somplaint:

Trunk floor heats up in the area of the left wheelwell

® Check clearance from tailmuffler to heatshield (specification about 25 mm) and frorn heatshield to underfloor of car (specification approx. 10 mm); adjust if necessary.

® Modified insulation matting in left side of trunk (Part No. 129 680 09 25). Production breakpoint 02.03.90.

® Floor covering of trunk (part no. as previously) with insulation liner on underside. Production breakpoint 01.02.90.

wie §=RA 07.3 1212/15 PR