Measuring crankshaft, fitting new bearings

WIS 03-3200

Preceding work: Operation no. of operation texts and work units or standard texts Crankshaft removed and flat rates: Engine disassembled, cleaned Crankshaft inspected, cleaned

Mounting crankshaft radially in bearings

Measuring crankshaft, fitting new bearings – rysunek

Crankshaft bearing cap …… stew eee eee install, tighten (80 Nm). Bearing bora Bw. ee ee snes measure, note. Crankshaft bearing journal @ 6. 66.0 ee measure, note (03-3190). Bearing shells 2… eee ee ee ee match, see table „Bearing shells for crankshaft”. Example: Bearing bore dia @ 62.51 mm Crankshaft journal @ – $7.95 mm. 4.55 min Radial bearing play -_0.04 mim 4.54 mrn : Bearing shell thickness

see table „Bearing shells for crankshaft” Top bearing shell “blue” . Bottorn bearing shell „blue”

A When determining different bearing shells, match thicker bearing shell to the bearing cap.

ghia RA 03.1225-3200/1 calculate. Likely radial bearing play …………0.008-

blow clean. Boltholes 0… ee ee ee ee eee sees Bearing shellS 21… ee ee eee . insert into crankcase and bearing cap. tighten (30 Nm). Bearing cap bolts ……… sewers oe Bearing @ oo… eee eee sees measure. Radial bearing play (real play)… 6… eee . calculate. (Specification 0.035–0.045 mm) Bearing cap …. occ ee tee ee eee sen . remove.

oil. Bearing shells in crankcase ……… seen Crankshaft at bearing points ………..08 0 oil. oil, install. Bearing caps with bearing shells ……….-. oil, install. Thread and contact surface of bolts ….. see

tighten to tightening torque and tightening BoltS … ccc ee wee eee cece ween sees angle (65 Nm + 90° tightening angle).

LN Rotate crankshaft while tightening the bolts in order to detect any jamrning in good time.

ageing RA 03.1225-3200/2

Measuring crankshaft, fitting new bearings – rysunek

P03-5359–57

Fit bearing width at crankcase and at fit bearing (ec) 6 ra measure, note. Fit bearing width at crankshaft …………05 measure, note. Thrust washers 22.2… 0… eee see eee match.

Ls Thrust washers of the same thickness must always be inserted on one side in the crankcase and in the bearing cap. The oil grooves must face toward the contact surface of the crankshaft and be oiled. The anti-twist lock is on the thrust washer in the bearing cap.

auth: RA 03.1225~3200/3

Likely axial bearing play see calculate. Axial bearing play with crankshaft installed …. measure. (Specification 0.100~0.250 mm).

Bearing diagram of crankshaft

Measuring crankshaft, fitting new bearings – rysunek

A Bearing shells in crankcase B Bearing shells in bearing caps

thio RA 03.1225-3200/4.

Measuring crankshaft, fitting new bearings – rysunek

crankshatt bearing.

Measuring crankshaft, fitting new bearings – rysunek

Permissible difference of fit bearing contact surfaces laterally from rectangularity related to the diarneter of the 1st and 7th crankshaft bearing point

and a bearing shell for the bearing cap. Paris with the replacement part additional indices 57, 58 and 60 are supplied individually and should be used only for the bearing cap (without oil groove}. %) The thickest point measured in the middle of the bearing shell is the relevant thickness.

cgiaintgn: RA 03.1225-3200/5

Test data

radial 0.030 – 0.045

axial 0.100 ~ 0.250

radial 0.020 – 0.050

Measuring crankshaft, fitting new bearings – rysunek
Measuring crankshaft, fitting new bearings – rysunek

Tightening torques in Nm or tightening angle

Measuring crankshaft, fitting new bearings – rysunek

Quick-calipers for internal measurements

Micrometer 0 ~ 25 mm 50 – 75 mm

cottage RA 03.1225-3200/6