With a modified engine, the engine output could be further increased for the 1935 season.
History
In addition to the version described in the technical specification sheet, this engine was also built in other, more powerful versions. The engine tunings were achieved mainly by an increase of the engine displacement; all engines were fitted with eight cylinders. The M 25 A was followed by the M 25 AB (bore/stroke 82/88, displacement 3710 cc, 398 hp at 5800/min), the M 25 B (bore/stroke 82/94.5 mm, displacement 3980 cc, 430 hp at 5800/min), the M 25 C (bore/stroke 82/102 mm, displacement 4300 cc, 462 hp at 5800/min) and, in 1936, the M 25 E (bore/stroke 86/102 mm, displacement 4740 cc, 494 hp at 5800/min).
General
Year
1935
Engine
Engine
Mercedes-Benz M 25 C
Design
8 cylinders with supercharger
Configuration
In-line engine with vertical cylinders
Cycle
Four-stroke
Cylinders
Cylinder head & cooling-water jackets welded together in blocks of 4 cylinders
Cylinder head
Welded on cylinder
Bore x stroke
82 x 102 mm
Displacement
4310 cc
Compression ratio
7.3
Output
462 hp at 5800 /min
Continuous output
462 hp at 5800/min
Max. engine speed
5800/min
Valve gear
2 overhead camshafts in separate housings
Intake valves
2 per cylinder, inverted
Exhaust valves
2 per cylinder, inverted
Crankshaft
Roller bearings, 9 main bearings,1 aux. bearing (compressor)
Carburettor / injection
Daimler-Benz special pressurised carburetter
Fuel supply
Junkers three-piston pressure pump
Lubrication
Pressure lubrication via lubricating pump
Cooling
Water circulation cooling, no fan
Electrical system
Ignition system
Bosch magneto ignition system
Ignition
Magneto ignition system
Firing order
1-6-2-5-8-3-7-4
Ignition timing
Automatically
Spark plugs
1 per cylinder, Bosch M 450 G 1
Lighting
Not fitted
Battery
Not fitted
Starter
Inertia starter
Drivetrain
Clutch
Mercedes-Benz dry single-disc clutch
Gearbox
Mercedes-Benz gearbox, 4 forward, 1 reverse gear
Shifting
Gate shift with locking system
Final drive
By cardan shaft to the rear axle
Gear ratios
Depending on the race
Axle ratio
Depending on the race
Chassis
Frame
Frame longitudinal member, U section
Front axle
Independent wheel suspension
Rear axle
Swing axle, leaf spring placed underneath, friction shock absorber
Steering
Screw-and-nut steering
Brakes
Hydr.-mech. brake system
Service brake
Acts on front and rear wheels (hydr.)
Front brakes
Inside shoe brake, air-cooled
Rear brakes
Inside shoe brake, air-cooled
Parking brake
Acts on rear wheels (mechanically via actuating cable)
Wheels
Wire-spoke wheels
Tyres front
5.50 x 19
Tyres rear
7.00 x 19
Dimensions and weights
Wheelbase
2725 mm
Track front
1473 mm
Track rear
1412 mm
Length
4040 mm
Width
1770 mm
Height
1160 mm
Vehicle weight
847 kg*
Weight (dry)
211 kg
Seats
1
Fuel tank
215 l
Performance
Maximum speed
bis ca.300km/h
Fuel consumption
84-98 l
Oil consumption
2,3-6,2 l
Remarks
Remarks
* Car weight without tyres, oil and water as per Formula: 750 kg.
General statements on the gearbox steppings cannot be made, as these were dependent on the track. The following transmission ratios were frequently used: I=1:2.0; II=1:1.3.7; III=1:1.14; IV= 1:0.80 In this case, thre rear-axle ratio was 4.44:1
Źródło: encyklopedia Mercedes-Benz na CD (1997). Tekst oryginalny po angielsku.