Leksykon

285 pojęć z techniki samochodowej i historii marki, od ABS po zapłon.

Źródło: encyklopedia Mercedes-Benz na CD (1997). Tekst oryginalny po angielsku.

A · B · C · D · E · F · G · H · I · K · L · M · O · P · R · S · T · U · V · W

A

ABS (anti-lock braking system)

With the help of ABS the pressure in the individual wheel slave cylinders (front and rear axle) is regulated so that even with full pedal force each wheel (especially on a slippery surface) continues to turn and can therefore brake optimally. The vehicle thus remains steerable.

(Locked front wheels make steering impossible, locked rear wheels lead to the car skidding or spinning.)

Function:

Wheel sensors inform the control unit of wheel revolutions. From these values the control unit allocates exactly the right pressure to each wheel slave cylinder so that optimal deceleration is achieved and the wheels do not lock.

ABS + ASR (trucks)

ABS und ASR (Anti-lock Braking System und Anti Skid Regulation) are only available together in Mercedes-Benz trucks for a good reason:
Just as ABS prevents a dangerous locking of wheels while braking and thus maintains driving stability and steerability while braking, ASR automatically prevents wheel-spin under acceleration. This results in decisive advantages for driving dynamics also for driven wheels on critical road surfaces.

Absorption-type muffler

With the absorption muffler the exhaust gases pass through a perforated pipe that is wrapped in sound-deadening materials (e.g. mineral wool or metal wool). The sound waves hit this sound-deadening material when they come through the holes and are more or less „absorbed” by them.

Active Body Control (ABC)

Active Body Control means active control of the movements of a vehicle’s body. ABC regulates the springing of a vehicle, keeps the vehicle horizontal and has a positive effect on handling by taking into consideration the forces currently acting on the wheels.

The functioning of this system is based on the following concept: The vehicle’s basic springs and conventional shock absorbers are arranged parellel to each other as usual. However, the body does not rest directly on the springs, but there is a controllable hydraulic cylinder between them. These cylinders have a double effect and can be adjusted by a pump and valve both statically and dynamically relative to movements of spring and body.

Adjustable flyweight governor (RQV governor) (trucks)

The adjustable governor differs from the two-stage governor in that each level of operating revolutions set at the control lever is held under various loads. It is necessary when auxilliary units such as pumps, winches etc. require a certain constant level of engine revolutions.

Aerodynamics

Aerodynamics is the science of the behaviour of moving bodies with respect to air, or wind, resistance. As air resistance grows in proportion with the square of speed, it is insignificant at low speeds, but with the rising maximum speeds of automobiles in the twenties and thirties aerodynamics became of increasing interest to design engineers. The streamline, or streamlining, was created; the first wind tunnel for measuring air stream behaviour had already been built in Göttingen in 1907.

Wind resistance (drag) is calculated according to the formula:

W = cw x A x V2 / 2g x y

Here A stands for the cross-sectional area of the vehicle.

The expression v2 : 2g

stands for driving speed, or velocity (v), the earth’s gravity (g) and the specific gravity of air (y) and is referred to as back pressure, ram pressure or dynamic pressure. The drag coefficient, which is due to surface friction and turbulence, cannot be measured, but can only be calculated according to the above formula with values measured in a wind tunnel.

Air brakes (trucks)

The transmission of brake pedal force to the individual wheel slave cylinders, including those on the trailer, by means of air pressure.

Air cooling

With air cooling the hot engine parts are cooled directly by the air stream or by air from a fan. Fins are necessary on cylinders, cylinder head and oil sump to increase the heat-conducting surface area. The Volkswageb „Beetle” was the most well-known car with an air-cooled engine.

Air suspension

With air suspension the elastic properties of an enclosed volume of air are used for springing. By changing the air pressure spring travel can be kept constant for the whole range of load conditions. By using a levelling system it is possible to keep the body of the vehicle at the same height while driving.
Air suspension with air chamber bellows (self-levelling) was first used in the Mercedes-Benz Type 300SE (W 112/3) in 1961 and was also standard equipment in the Type 600 (W 100).

Anti-dive device

An anti-dive device means a feature of the front axle that prevents the front of the car from sinking when the brakes are applied.

Anti-knock properties

According to the compression ratio of an engine, fuel with higher or lower anti-knock properties must be used. The Research-Oktan-Zahl (ROZ) gives an indication of the anti-knock properties of petrol.
Normal petrol for engines with low compression has at least 91 octanes, super petrol for engines with high compression has 95 octanes („Euro Super”) or 98 octanes („Super Plus”).
The octane index of a fuel is tested in a test engine, the compression of which is adjusted for so long during the test until a certain level of knock is reached. A comparative fuel is then mixed out of iso-octane (100 octanes) and n-heptan (0 octanes) that shows the same knock. The mix-ratio of this fuel is then the octane figure of the fuel being tested.
The test conditions to be maintained with the test engine have to be adapted to the practical operating conditions of the engine, in order to determine the expected knock in petrol engines.

Anti-roll bar

In addition to springs and shock absorbers, anti-roll bars (or stabilizers) are also often fitted to vehicles. Anti-roll bars usually consist of a rod with a round cross-section bent into a U-shape with each end connected to the wheel control elements of either both front wheels or both rear wheels. The purpose of anti-roll bars is to harden springing when there is spring travel on only one side of the vehicle or when spring travel alternates from one side to the other. They help to resist the leaning or rolling of a vehicle’s body in bends and thus improve handling. If there is equal spring travel on both sides of the vehicle, anti-roll bars have no effect.

Aquaplaning

Aquaplaning means the phenomenon of a tyre „floating” on a thin film of water on a road surface because a wedge of water has forced itself under the tyre’s entire contact area, which lifts it from the road surface.
While aquaplaning a vehicle cannot be steered or braked properly.

ASR

ASR stands for automatic skid regulation. ASR regulates propulsion forces automatically and ensures that the driven wheels do not spin or skid due to excessive use of the accelerator pedal.

Automatic gearbox

Automatic gearboxes usually consist of a torque converter or a hydraulic clutch and several sets of planetary gears that are integrated into one unit. .
With automatic gearboxes there is no need to operate a clutch pedal. Gears are changed automatically depending on driving speed, engine speed, position of the gear lever and of the accelerator.

Auxiliary range gearbox (trucks)

An additional pair of gear wheels or a planetary gear set with syncromesh shifting as a supplement to the main gearbox. This doubles the number of gears available and thus utilises engine power better.

Axles

In the main, independent wheel suspension is used on cars nowadays. Rigid axles are used only at the rear (driven as well as undriven).

B

Band-spring clutch

In 1900 the Daimler-Motoren-Gesellschaft introduced the so-called „band-spring clutch” to improve drive-away characteristics (e.g. in the Mercedes „Simplex”). In fact this was more of a low-speed traction control device, as power transmission was initiated by winding up a tensioned coiled band-spring. This type of clutch was used until 1912, when it was replaced by the leather double-cone clutch.

Battery

The battery supplies the vehicle with electrical energy while it is standing. If the vehicle has a high requirement for electricity while it is moving the battery can supply electricity with the generator. With normal electricity consumption, while the engine is running, the battery is charged by the generator (alternator), so that it can supply electricity at any time.

When the engine is idling, especially in winter, the electricity generated by the alternator may be considerably less than that which is actually required, however.

Battery ignition

Battery ignition is the successor of magneto ignition or also touch and spark ignition.
Experiments were carried out with battery ignition before magneto ignition, but as cars had no generators batteries quickly ran flat and so battery ignition appeared again – improved – in the thirties.

Classical battery ignition consists mainly of ignition coil, capacitor, contact breaker, distributor and spark plugs. Ignition energy and voltage are limited, however, by the electrical and mechanical switching capacity of the contact breaker and if excessive can lead to current reduction or burnt contacts.

To achieve a more stable ignition system contact-controlled or contactless ignition was developed.

Belt car

The Daimler car of 1894 with a 2-cylinder, 1.8 KW (2.5 h.p.) engine was known as the belt car. With this car power transmission was by a 4-speed system of belt gears from the engine to the rear wheels. This made a very smooth gear change possible. Daimler favoured this type of gearbox for a long time, although Wilhelm Maybach had already presented the cogwheel gearbox as a promising alternative in his car with steel-spoked wheels.

Bevel gear and differential ring gear

With front-engined, rear wheel drive cars the differential is driven by bevel gear and differential ring gear. These gears have spiral or hypoid toothing. Nowadays hypoid gears are almost always used with the bevel gear offset from the middle of the differential ring gear. This means that the propeller-shaft can be set lower and thus also the car’s transmission tunnel.

Bore

The word bore denotes the inner diameter of a cylinder.

Brake system

A car’s brake system includes:

Master brake cylinder with fluid reservoir (sometimes with brake servo), brake lines made of metal and rubberised fabric, wheel slave cylinders, brake shoes and brake drums in the case of drum brakes; brake callipers, brake pads and brake discs in the case of disc brakes. The parking brake is operated by cable.

Brake, automatic load-dependent (trucks)

With automatic load-dependent brakes the regulation of braking force takes place according to the load condition of the vehicle. Spring travel is transmitted to a pressure sender by a rod linkage.

Breakerless transistor ignition

This system is the same as transistor ignition in principle, with the difference that the cam-actuated contact-breaker in the distributor is replaced by an ignition pulse generator, which activates the electronic ignition by electrical impulses without the use of a mechanical contact-breaker.

C

Cam disc operation

With this form of valve operation a cam disc is fitted to the crankshaft. The valves are operated by a rod, which is guided by the cam disc. The cam disc has a goove that goes around the crankshaft axis twice and leads back into itself. The groove is laid out so that it corresponds with four-stroke valve operation. The engine’s revolutions are regulated by a movable tongue at the point where the groove crosses itself. At certain engine revolutions the control rod is guided from the working groove into the idling groove by this tongue. Although Daimler’s patent specification (DRP 28243 of 22 December 1883) for this type of valve operation foresaw the control of both inlet and outlet valve in this way, with the „grandfather clock” only the outlet valve was controlled. This type of valve operation is only suitable for single-cylinder engines.

Camber

Wheels do not stand exactly at the vertical, but lean at a certain angle. This angle is called camber. According to the direction of this lean, camber is either positive or negative.

Positiver camber = the point of contact between tyre and road is nearer to the longitudinal axis of the car than the top of the tyre.

Negativer camber = the point of contact is further from the axis than the top of the tyre

Car with wire-spoked wheels

Daimler’s car with wire-spoked wheels was presented to the public at the world exposition in Paris in 1889. After the exposition it remained in France. Its V-twin engine (developed by Wilhelm Maybach) served as a model for licence production by the French automobile manufacturers Panhard & Levassor und Peugeot.

Carburettor

Vehicles with combustion engines usually carry their fuel with them in liquid form. As combustion is only possible, however, in a gaseous form in combination with oxygen, the fuel must be prepared for combustion. This means that the fuel must be atomised and mixed with the right volume of air for the engine’s current operating conditions.
In the case of the petrol engine the carburettor or the petrol injection system perfom this function, with the diesel engine it is the diesel injection system.

According to the flow direction of the mixture one can differentiate between down-draught, cross-draught and up-draught carburettors. According to the number and function of mixing chamber one differentiates between single carburettors with one suction pipe, twin carburettors with separate suction pipes and dual- or multi-stage carburettors with stages opening consecutively with single or separate suction pipes. Higher requirements for mixture and exhaust gas quality during the eighties meant that the use of the carburettor became less and less popular; its job was done more and more by the petrol injection system.

Castor

The inclination to the longitudinal of the axes of rotation of the steering axle stub and the suspension strut is called castor, whereby the lower pivot point is further than the upper from the transverse axis of the vehicle. The tracking point (imagined intersection of the extended axis of the castor angle and the road surface) is therefore in front of the point of contact of the tyre. (This means that the wheels are pulled by the car and when they are turned in a bend a force arises that brings the wheels back to the straight ahead position automatically after the bend when the steering whell is no longer turned.)

Catalytic converter

The most effective way of cleaning the exhaust gases of a petrol engine is currently the use of the three-way catalytic converter. The original meaning of the word catalyst is a material that makes possible or accelerates a chemical reaction, whereas the material itself undergoes no change. The three-way catalytic converter is one which converts or reduces the three main polluting constituents of the exhaust gases resulting from the combustion process.

Centrifugal timing device

The centrifugal timing device turns the cams that are movably mounted on the distributor shaft in the direction of rotation with the help of flyweights. This regulation is dependent on engine revolutions (the higher the revolutions, the further the cams are turned).

Chain drive

With chain drive the power of the engine is transmitted directly to the rear axle via an intermediate gearbox and chains (usually two).
Chain drive was used on almost all cars in the early days of automobile engineering. It was already known from steam engines and was the stage of development before shaft drive with universal joints. Even a powerful car such as the Blitzen-Benz (1911) used chain drive.

Chassis and running gear

A vehicle’s chassis and running gear consist of the chassis or body platform, the suspension, front and rear axle, steering, brakes and wheels with tyres.

Cars usually have no actual chassis, but integral bodywork. With this construction the floor platform is welded to the rest of the bodywork so that a high load-bearing capacity and stiffness are achieved.

All the above mentioned components are connected to the self-supporting body, either directly or with rubber dampers.

Chassis and running gear according to DIN 70020 (trucks)

The weight of chassis and running gear ready for operation including all components that are delivered with as standard equipment.

Also included in the weight are:

– full fuel tank
– full radiator
– oil in engine, gearbox and axles
– complete electrical equipment with charged battery
– standard tyres and spare wheel
– dashboard
– windscreen
– tools

the following are not weighed:

– cab and body
– trailer coupling
– jack
– fire extinguisher
– auxilliary drives

Classification of piston engines

The internal combustion engines used in vehicles are classified into the following two main groups according to the fuel used and the working principle of the engine.

Petrol engines:
run on light fuel. Combustion in the cylinder with externally supplied ignition.

Diesel engines:
run on heavy fuel. Combustion in the cylinder with spontaneous ignition in the highly compressed, hot air.

With both main groups there is a difference between:

– working principle: exchange of gases by four-stroke or two-stroke operation.
Four-stroke engines need four piston strokes to complete one working cycle = 2 crankshaft rotations.
Two-stroke engines need two piston strokes to complete one working cycle = 1 crankshaft rotation.

– The method of cooling: liquid-cooled and air-cooled engines.
– The configuration of the cylinders: in-line engines, horizontally opposed engines and V-engines.
In-line engines – cylinders aligned in a line.
Horizontally opposed engines – cylinders arranged opposite each other.
V-Engines – cylinders configured in a V-form (as a rule 60° oder 90°).

Clutch

The clutch transmits torque from the engine to the gearbox. It is a connection that can be interrupted. With friction clutches power transmission is interrupted by operating the clutch pedal, with hydraulic clutches or torque converters it depends on revolutions.

Clutch brake (trucks)

This is a device on the gearbox drive-shaft that brakes the rotating masses of the driving disc and the gearwheels. This works by friction between two surfaces, which are brought together by a conical spiral spring when the clutch is operated. Gears can thus be shifted relatively quickly with a constant-mesh countershaft gearbox.

Coil spring

The coil spring (wrongly also called spiral spring) consists of spring steel wire wound into a coil. Its small size means that it can be installed without taking up much space.
As coil springs cannot take on any transverse or longitudinal forces they are only used with axles that are suspended on radius arms.

Cold start

The colder a combustion engine is, the worse it starts. Cold starting should therefore be facilitated by:

– using winter oil or multi-grade oil
– checking the condition of the battery
– separating the engine from the gearbox by operating the clutch
– switching off all electrical devices before starting the engine

Compression ratio

The compression ratio „epsilon” is the ratio of engine capacity plus compression chamber to compression chamber.

„epsilon” = capacity + compression chamber : compression chamber

Compressor

Compressors were originally developed for aeroplanes in the middle of the First World War. The reason for their development was to compensate for reduced performance with increasing altitude.

The compressor is a supercharger for the improvement of cylinder filling, which can be switched on and off, or which rotates permanently. The mixture is „blown” into the combustion chamber under pressure and in this way output is boosted.

From 1921 compressors (Roots blowers) were also used in cars, in the Mercedes 6/25/40 h.p., for example. The first figure stands for output in horsepower measured according to a tax formula that was usual at that time, the second figure stands for actual horsepower without compressor and the third figure stands for actual horsepower with compressor.

From 1924 the compressor was used in large, sporty Mercedes models, for example, in the Type 400 und 630, in the legendary „S” sports cars (models „S”,”SS”, „SSK”,”SSKL”), later in the Types 500K und 540K, as well as in the prestigious luxury limousines „Large Mercedes” (W 07) und Type 770K (W 150). Of course, all formula racing cars were equipped with compressors.

After the Second World War the compressor concept was no longer pursued until the appearance of the C-Class model C 230 and the SLK 230, both with compressor.

Compressor for compressed air (trucks)

Single or dual-cylinder piston compressor, driven by the engine, that supplies compressed air for the brake system.

Compressor, modern

The classical compressor era at Mercedes-Benz ended in the late thirties. Cars with compressor engines only returned to series production in 1995. The air supply system was especially re-designed for the 4-cylinder engine with mechanical supercharging and intercooling. Due to the mechanical coupling between compressor and engine, torque is built up almost without any delay at all.

Compresssion chamber

The compression chamber is the space remaining above the piston after it has reached top dead centre (TDC). The combustion of the fuel/air mixture begins here.

Condensor

The capacitor is switched in parallel to the contact breakers. It takes on the electrons that have come into movement because of the self-induction tension (in the coil) and in this way ensures that the magnetic field in the ignition coil can be interrupted suddenly and without serious sparking. In this way wear and tear of the contact breakers can be kept within reasonable limits and ignition voltage can be increased.

Connecting rods

The connecting rods connect the pistons with the crankshaft. They take the forces acting on the pistons and produce a torque acting on the crankshaft.

Constant vacuum carburettor

The constant vacuum carburettor differs considerably from other types of carburettor.
Whereas all other carburettors have a barrel with a certain diameter and have a separate jet system for idling, part-load and full-load, the constant vacuum carburettor has a barrel with a variable cross-section and only one jet for metering the fuel. This jet has a conical needle in its opening, the size of which is increased or decreased by movements of the accelerator pedal.

Constant-mesh countershaft gearbox

There is only one major difference between the construction of a constant mesh countershaft gearbox and a synchromesh gearbox. With these gearboxes there is no bevel clutch between selector sleeve and gearwheel.
As it is also necessary to have the selector sleeve and the gear wheel at equal speeds in order to get a gear, this effect is achieved by double declutching (when shifting up) or so-called blipping the throttle when changng down.

Contact breaker

The job of the contact-breaker is to interrupt the electrical circuit in the primary coil so that the magnetic field in the ignition coil can be built up again and again. It consists of a contact-breaker arm, the stationary arm and the cam, which is driven by an intermediate drive so that it turns at half crankshaft revolutions. The number of ridges on the cam corresponds with the number of cylinders. This means that the magnetic field in the coil is built up and collapses as many times as the number of cylinders in the engine and that this number of sparks is produced.

Cooling

Heat arises from combustion in the cylinders. This heat has to be dissipated so that the engine does not overheat.
The heat can be dissipated by means of water, air or oil. One therefore speaks of water-cooling, air-cooling and, occasionally, oil-cooling, which is used in combination with air-cooling.

Crankshaft

The crankshaft converts the reciprocating movement of the pistons into a rotary motion and transfers this to the wheels via the clutch, gearbox and differential.

Cross-draught carburettor

With the cross-draught carburettor the mixture flows to the cylinder horizontally. This type of carburettor is mainly to be found where there is too little room for the carburettor(s) above the cylinder head.

Cross-ply tyres

With cross-ply tyres the layers of fabric (or textile) are laid out at an angle of 37-40° to the tyre’s central axis. With this angle the tyre is relatively soft and has good springing characteristics. A disadvantage is expansion in a radial direction upon heating.

Cruise control

In combination with automatic transmission cruise control ensures that a selected speed is held. Cruise control maintains the speed constantly until the driver uses the brakes, when cruise control is switched off automatically. If the driver accelerates, the car returns to the speed selected by the cruise control after acceleration is completed.

Crumple zone

In the case of a collision the momentum of a moving vehicle must be converted into deformation energy in a very short time so that the load acting on the occupants is minimised. The front and rear of the car are therefore designed as „crumple zones” with defined deformation. This deformation is tested and measured in extensive crash tests. Mercedes-Benz was the first automobile manufacturer to carry out these comprehensive tests and include them in its standard programme.

Cylinder

The cylinders guide the pistons and provide the sealing to the sides against working pressure. They also conduct the heat generated by combustion to the cooling fluid.

Cylinder head

The cylinder head used to be made of grey cast iron but is now usually made of light alloy and closes the cylinder at the top.
With petrol engines it includes the spark plugs and in the case of four-stroke petrol engines also the inlet and outlet valves. With diesel engines it includes the inlet and outlet valves, the pre-chamber or swirl chamber, injection nozzles and heater plugs.

D

Daimler’s first experimental engine

Maybach und Daimler wanted to construct an engine that would be independent of the gas supply network. The engine they completed by the middle of August 1883 had a cylinder cast in bronze with a horizontal configuration and an output of about 1/4 h.p. at 600 r.p.m.

Daimler’s two-cylinder engine

Wilhelm Maybach developed his V-twin engine based on the „grandfather clock engine” in 1888. This engine was first installed in the car with wire-spoked wheels.

De Dion rear axle

This type of rear axle was designed by Marquis De Dion already in 1893 according to the principle of „low unsprung weight”. With this design the differential and the rear axle housing are separated, driving torque is supported by the floor of the vehicle and the axle body’s movements are controlled by longitudinal leaf springs or by guide rods. Driving torque is transmitted by half-shafts with universal joints to the driven wheels. This complex rear axle construction was first used by Daimler-Benz in the formula racing car W25 (1936 season).

Desmodromic valve operation

Valve operation whereby the valves are not closed by springs, as is usual, but by separate rockers and cams. Mercedes-Benz used this system in the formula 1 racing car of 1954/55, the W196, and its derivates.

Diagonal control arm (semi-trailing arm)

Diagonal control arms (semi-trailing arms) are installed at a diagonal to the longitudinal axis of a vehicle. As A-arms they are used to control individual wheels. The axis of rotation of the arm is diagonal to the vehicle’s longitudinal axis.

Diagonal swinging axle

With this design of axle the wheels are suspended independently of each other on A-frame arms, the pivot axes of which run diagonally to the car’s transverse axis. The differential is firmly connected to the axle bracket. The wheels are connected to the differential by drive-shafts with two universal joints each.

Diaphragm brake cylinder (trucks)

Compressed air acts on a spring-tensioned diaphragm, the movements of which are then transmitted to the wheel brake by a rod linkage.

Diesel direct injection

Direct injection is in principle the easiest way to get fuel into the combustion chamber. The nozzle sprays the jet of fuel into a hollow part of the top of the piston. Direct injection is characterized by very low fuel consumption, but in terms of pollutingemissions it is not entirely unproblematic and also causes a very harsh combustion noise.

Diesel engine, 1st production car with a diesel engine

After the diesel engine had proved itself in commercial vehicles it was also put to use in cars. In February 1936 the first series production car with a diesel engine, the Mercedes-Benz Type 260 D, was shown at the automobile exhibition in Berlin.
The 4-cylinder diesel engine had the same size of cylinder as the 3.8 litre 6-cylinder engine „Type Mannheim” and worked on the pre-chamber principle.

Diesel in-line injection pump

The injection pump is a piston pump. For every engine cylinder it contains a pump element consisting of cylinder and piston. The piston of this element is lifted by a cam and pressed back again by a spring.
Fuel is metered by a metering ramp (helix) on the piston shaft. The volume of fuel transported depends on the rotation of the piston.

Diesel injection

The main components are the injection pump and the injection nozzles, as with petrol injection.
A fuel feed pump draws the diesel fuel out of the tank and transports it under a slight pressure through a fuel filter to the inlet chamber of the injection pump, which then forces the fuel through the high pressure lines to the injection nozzles.
A difference exists between direct and indirect injection (pre-combustion chamber injection).

Differential

It is the job of the differential to transmit the torque supplied by the engine evenly to the rear axle (and therefore to the drive wheels). In addition it has to compensate for the difference in speed between the outer wheel and the inner wheel when driving around a bend. (The wheel on the inside of the bend travels a shorter distance than the wheel on the outside, it therefore performs fewer revolutions.)

In connection with cars there is not only the conventional differential, but also the limited slip differential. The latter makes it possible to achieve an optimal transmission of torque to the rear wheels even with differing road surfaces under the two rear wheels.

Differential

The differential allows the wheels of an axle to rotate at different speeds in a bend.

Differential lock

The differential lock switches off the compensating function of the differential or limits it so that the vehicle has more traction in difficult terrain (sand, mud). The differential lock is usually operated electro-pneumatically.

Differential with limited slip

The automatic balancing of a conventional differential makes power transmission impossible if one of the driven wheels lifts off the ground or loses grip on ice or another slippery surface.
(This wheel spins at double speed while the other wheel, which has grip, is not driven and stands still.)

Function:
The separating force that arises between the balancing gearwheels and the shafts’ driving gears exhert an axial pressure on friction plates which produce power transmission between the two drive shafts. If one wheel loses grip the torque that has been built up acts on the other wheel. Tractive force is thus maintained.

Differential, conventional

Power transmission is from the egine to the pinion wheel, which engages with the crown wheel.
The crown wheel is firmly mounted in the differential housing. The balancing bevel gears, which engage with the two driving gearwheels of the drive shafts, are supported in bearings in this housing.

When the vehicle is travelling in a straight line the driving gearwheels turn at the same speed. The balancing gearwheels do not turn, but circulate with the balancing housing; they work as drivers and transmit the driving forces equally to both wheels.

When driving in a bend the driving gearwheels turn at different speeds. The balancing gearwheels now rotate around their own axes and roll on the driving gears.

In this way, with equal torque distribution, the speed of the wheel on the inside of the bend is reduced by the same amount that the speed of the outer wheel is increased.

Direct injection method

With this method the fuel is injected directly into the cylinder through the injection nozzles. To improve the turbulence of the resulting fuel-air mixture the combustion chamber is usually continued into the top of the piston as a hollow or hemispere. So that the fuel particles can make their way through the highly compressed air in the cylinder, very high injection pressures have to be used, unlike with other systems.

Disc brakes

Disc brakes consist of a brake disc, which turns with the wheel and a brake calliper, which contains brake cylinders and brake pads.

Function:
When the brake pedal is operated, brake fluid pressure pushes the two brake calliper pistons against the brake pads. The pads create friction on the brake discs, which decelerates the discs and therefore also the wheels.

Distributor

The distributor consists of a distributor disc or distributor cap with connections for the high-tension cables and the rotor arm, which is fitted on the contact-breaker cam. The distributor carries out the following functions: breaking the primary electrical circuit, distributing the high-tension electricity to the spark plugs of the individual cylinders and advancing and retarding the ignition timing (by means of flyweights and vacuum).

Distributor injection pump

Unlike the the in-line injection pump, the distributor injection pump has only one cylinder and one pump piston which also acts as a distributor. The fuel is distributed by this piston in exactly measured volumes to the injection nozzles of the individual cylinders.

Distributor rotor arm

The distributor rotor arm distributes the high-tension electricity. This electricity comes from the ignition coil, through the middle of the distributor cap to the rotor arm, which tranfers it to the individual cylinders at the right time.

Downdraught carburettor

With the downdraught carburettor the mixture flows in the direction of gravity into the cylinders. As this flow direction is achieves an efficient filling of the combustion chamber the downdraught carburettor is the most commonly used type of carburettor.

Drag coefficient

The drag coefficient, also known as the Cd value, is the specific value for every shape of car body, the thing that determines a car’s wind resistance. The Cd value cannot be measured directly, however, but can be calculated from values determined in a wind tunnel.

The formula for calculating the Cd value is:

Cd= Wl / F x q

i.e.: The drag coefficient is given by the measured wind resistance divided by cross-sectional area multiplied by back pressure.

Drive-through axle

The second rear axle is driven by a drive-through device fitted on the first axle. The drive-through is fitted with a compensating device that prevents any tension from arising between the two axles.
This construction makes the use of a transfer case or power divider and a second propshaft unnecessary.

Drum brakes

Drum brakes are now seldom used on cars, and if at all, then on the rear wheels. Drum brakes consist of an anchor plate on which the wheel slave cylinder and the brake shoes are mounted, the former fixed and the latter moveable. The brake drum is fitted to the axle and turns around the anchor plate.

Function: When the brake pedal is operated, pressure from the master cylinder pushes the pistons in the wheel slave cylinders apart and, as a consequence, the brake shoes against the inside of the brake drum. The friction that arises decelerates the brake drum and therefore also the wheel that is fitted on it.

Dry sump lubrication

With this type of lubrication the oil is kept in a reservoir separate from the engine. It is drawn from this reservoir by a pump and transported to the lubricating points. A second pump constantly draws the oil from the dry sump below the crank-case and returns it to the reservoir. The oil-air mixture is then „de-foamed” as it arrives here.

Dual-circuit brake system

Front and rear wheels are braked by two independent circuits. If one brake circuit fails, the other is still intact, which means that the vehicle’s brake system still has some effect.

Dual-line trailer brake

With this system two brake lines lead to the trailer: a filling line and a control line. The filling line constantly supplies the trailer reservoir with compressed air, even during braking. The control line activates the brakes. In this case the trailer is not braked by the release of air, but by a pressure rise, just like the tractor unit. If the trailer should break away, a reversing valve connects the reservoir wih the wheel brake cylinders and the brakes are fully engaged immediately. The main advantage of the dual-circuit brake system is the fact that this brake cannot be exhausted even when driving down long gradients.

Dual-ratio rear axle (trucks)

Rear axle with two transmission ratios; the second ratio with the lower gears is approximately in the middle of the gearbox ratios and thus has the function of an intermediate gear. Change-over can be pneumatic or electro-pneumatic.

Dual-stage spring (trucks)

Dual-stage springs consist of the main spring and a supplementary spring. When the truck is empty or only lightly loaded only the main spring works, at approximately half load the supplementary spring begins to work progressively.

Dynamo

Shunt-wound generator with parallel switched anchor and exciter winding. The generator charges the battery and provides electricity for the vehicle, not when the engine is idling, however. A cutout relay maintains a constant voltage at all revolutions.

E

Electrical roller cell pump

Electrical roller cell pumps are the main type of pump used for petrol engines with fuel injection. An electric motor drives a rotor disc that is mounted excentrically on a bearing in a housing. The rotor disc has pocket-shaped hollows in its circumference, with a metal roller in each of them. These rollers are pressed outwards by centrifugal force during rotation and act as a seal. A suction and feed effect arises from the fact that due to the sealing rollers, periodically a volume is expanded on the suction side and reduced on the pressure side.

Electronic-Stability-Program (ESP)

ESP (Electronic-Stability-Program) includes all functions of ABS, ETS und ASR such as Traction support and a stabilising effect while braking and accelerating. ESP also reduces the risk of skidding in a bend – up to the limits of physics – and keeps the car stable even during extreme avoidance manoeuvres. If necessary one of the wheels, front or rear, is braked automatically and engine performance is reduced or even increased.

Empty weight

Weight of a vehicle ready for use, i.e. with a full tank and including all equipment (spare wheel, tools etc.), but unloaded.

Engine block

The engine block is a casting, nowadays often made of a light alloy that contains the cylinder barrels as well as (with water-cooled engines) the coolant ducts. The lower part of the block leads into the so-called crankcase. The block is closed at the top by the cylinder head.

Engine brake (trucks)

By operating a throttle valve in the exhaust manifold the exhaust gases are blocked and thus the engine is braked. When the engine brake is used the accelerator and clutch pedals are locked to avoid the danger of driver error. The engine brake can be operated by a lever on the steering wheel or a compressed air valve on the floor.

Engine capacity

Cubic capacity of an engine’s cylinders in cubic centimetres (cc), measured as follows:

r x r x pi x s

oder r² x pi x s

r = bore radius in cm
pi = 22/7 (approx. 3,14)
s = stroke in cm

Engine, 4-cylinder, 4-stroke

Most internal combustion engines nowadays work on the so-called four-stroke principle, which classifies the events in the combustion chamber according to four distinctly different strokes of the piston:
1. intake stroke
2. compression stroke
3. working stroke
4. exhaust stroke

EPS (Elektro-pneumatic gear-shift) (trucks)

EPS (electro-pneumatic shifting) in the integrated drive concept of Mercedes-Benz trucks is available in connection with 8-cylinder V-engines with turbocharging and intercooling and 16 speed gearboxes.

Gears are selected by finger pressure and engaged pneumatically when the clutch is operated. Rapid shifting is therefore possible and due to the carefully laid-out gearbox ratios it is possible to drive with the optimal engine revolutions, which means reduced fuel consumption. It is also possible to prevent inappropriate gear changes – the driver is warned of this danger by an acoustic signal. Therefore the engine cannot be over-revved by selecting too low a gear.

Evaporation cooling

With evaporation cooling there was no closed cooling circuit. The water used for cooling evaporated and was lost. Engines with evaporation cooling therefore had a high water consumption, which meant that engine output could not be increased for a long time.

Exhaust system

The gases flowing through the exhaust ports in the cylinder head are led into the exhaust manifold and from there through one or two pipes into the front muffler (single or double exhaust gas ducting). From here they flow into the middle muffler and rear muffler and then through one or two exhaust pipes into the open air.

Exhaust-gas turbocharger

The engine’s exhaust gases drive a turbine that is connected to a radial compressor, which in turn forces air into the cylinders.

Due to the larger volume of air more fuel can be injected, which leads to a performance boost of up to 30%.

The „exhaust turbocharger” developed by Dr. Sanford Moss in the First World War was first used in aeroplanes. The first series car in the world with a petrol engine and exhaust turbocharger was produced by General Motors in the USA in 1963. The principle became more important during the oil crisis of the 70s. The exhaust turbocharger – a turbine machine – is not mechanically coupled to the engine, but is connected thermo-dynamically. A small turbine installed in the exhaust manifold is driven by the exhaust gases. A so-called bypass valve regulates the pressure and lets someof the exhaust gases directly into the exhaust system. The blower of the turbocharger is fitted to the same shaft in a separate chamber.

F

Fading

Fading means a temporary reduction of braking efficiency.

Fan

As not enough air flows through the radiator when the car is motionless or moving at a low or medium speed, vehicles with combustion engines have a fan. The fan has several blades. It is driven either by a drive belt from the engine’s crankshaft or by a separate electric motor. In the first case the fan can be firmly mounted on a shaft (i.e. it always rotates) or can be separated by a fan clutch regulated by temperature or revolutions. (i.e. it rotates only when the coolant exceeds a certain temperature or rotates only to certain maximum revolutions.

Fluid cooled (water cooled)

Although one normally speaks of water-cooled engines the correct expression is actually fluid-cooled as the coolant is a mixture of water and anti-freeze fluid with an anti-corrosion component. With this cooling system the coolant is circulated by a pump that is operated by the engine. If the engine is cold the coolant only circulates inside the engine block. The thermostat only lets the fluid into the radiatior after a certain temperature has been reached. The cooling fluid then circulates from the pump, through the engine block, to the radiator and back to the pump.

Flywheel cooling

One of the main problems with early motor vehicles was cooling. The evaporation coolers, which were in use until 1892, required large quantities of water so that drivers were constantly obliged to keep a look out for wells or streams in order to fill up their water tanks. Wilhelm Maybach had the idea of using the inside of the flywheel for cooling purposes. Water was filled into a groove inside the flywheel where it was held by centrifugal force. When required it was fed back into the cooling circuit through a jet. Maybach received patent number DRP 70 260 for this cooling device in 1892.

Four-cylinder engine, the first

Wilhelm Maybach constructed the first four-cylinder engine in the world in 1890. It was originally intended as a boat engine and had an output of 5 h.p. at 620 r.p.m.

Friction clutch

Dry single-plate clutches are usually used in cars with manual transmission.
They consist of:

Clutch cover, which in turn includes the release plate, the release lever, the pressure plate and either a central diaphragm spring or several, depending on the type of clutch.

Clutch plate, running on the splined drive shaft from the gearbox with clutch linings on both sides.

Thrust bearing, connected to the clutch pedal by the release fork (either by a cable, rod linkage or hydraulics similar to the brake system)

Function:
The thrust bearing is pushed against the release plate when the clutch pedal is depressed, the release plate lifts the pressure plate from the clutch plate against the spring pressure with the release fork and the connection is then broken.

Front wheel drive

Front wheel drive means that the engine drives the front wheels. In order to combine drive and steering, movable drive-shafts have to be used.

Fuel feed pump

Either piston pumps or diaphragm pumps are used to feed fuel from the tank to the carburettor or the injection pump. The pumps are driven either electrically or mechanically.

Fuel pump, mechanical

With mechanical pumps the diaphragm or the piston is moved up and down by a tappet or a lever. This tappet or lever runs on a camshaft which is driven by the crankshaft of the engine. A mechanical fuel pump therefore has to be flanged directly onto the engine block or cylinder head.

G

Gearbox

Combustion engines have the peculiarity of only producing a useful torque within a certain range of revolutions.
In order to stay within this range at all driving speeds a gearbox is necessary to obtain the required ratios.

Gearbox

Transmission with manual gearbox (components):

1) clutch
2) gearwheels
3) synchromesh
4) reverse gear
5) cardan shaft
6) differential
7) bevel gear
8) ring gear
9) gearbox housing (clutch bell-housing integrated)

Automatic gearbox (construction):

1) torque converter
2) reactor
3) internal ring gear
4) brake band
5) clutches
6) sun gear
7) planetary gears
8) planetary train
9) pump wheel
10) turbine

Gearbox, syncromesh

There is a major difference between a simple gearbox and a synchromesh gearbox. With the former it is only possible to change gear by moving the gearwheels, whereas with the latter all pairs of gearwheels are constantly engaged.

Different ratios are obtained by moving selector sleeves. One gearwheel of each pair is firmly connected to the countershaft, whereas the other gearwheel is able to rotate freely on the main shaft. To select a gear the free gearwheel is fixed to the main shaft by dogs. These dogs are located on the inside of the dog-ring and also on the gearwheel to be selected.

Before the gear can be selected, both parts have to rotate at the same speed. When shifting at first small bevel clutches are activated, which either brake or accelerate the appropriate gearwheel until both have the same revolutions. Only then can the gear be engaged.

Generator

Voltage is induced in the generator by conductors cutting through magnetic field lines. The generator is driven by a drive belt from a pulley on the crankshaft. There is a difference between direct current generators, usually called dynamos, and alternating current generators (alternators).

Generator, alternator

The advantage of this generator over the direct current generator is that it produces electricity when the engine is idling. The excitor winding is supplied by slip rings. Alternating current is taken off by the stationary stator windings and conducted to the rectifier.

Gradient

Gradient refers to a road surface that runs at a certain angle to the horizontal.

Gradients are expressed in % figures. A gradient of 100 % is equivalent to an angle of 45° to the horizontal.

Calculating example:

Gradient = H x 100 / L = 30 x 100 / 100 = 30 %

Grandfather clock

Nickname for the first vertical single-cylinder experimental engine by Gottlieb Daimler and Wilhelm Maybach (1885), the shape of which resembled a grandfather clock.

H

Handbrake servo (trucks)

Servo assistance for the force needed to operate the handbrake. The illustration shows a compressed air servo unit. If air pressure falls a ball lock holds the linkage in braking position.

Heater plug

With pre-chamber and swirl-chamber diesel engines heater plugs are required for starting the engine at low temperatures to compensate for the cooling of the fuel on the cold sides of the chamber and so to facilitate combustion.
When the engine is running the temperature in the cylinders is so high that the heater plugs can be switched off.

High tension condenser ignition

High tension capacitor ignition also called thyristor ignition was developed for high performance high revving engines for sports cars and racing cars. Unlike the ignition systems of „normal” vehicles ignition energy is not stored in a magnetic field, but in the electric field of a capacitor. A thyristor is used as a high performance switch, an ignition transformer is used to convert the primary tension from the capacitor charge to the high voltage required.

High-tension magneto

High tension magneto ignition has the following main components: a generator to produce alternating current consisiting of a magnet, an anchor, contact breaker and distributor.

Function:
The electricity that is produced in the primary winding is interrupted every half revolution, whereby the magnetic field jumps and transmits high tension electricity to the secondary winding that is also on the anchor. This electricity then produces a spark at the spark plug.

Honeycomb radiator

he secondary current was short-circuited and the sparking stopped.

Horsepower

Unit of measurement of the Society of Automotive Engineers (SAE) for engine power. 1 horsepower (h.p.) corresponds to the power needed to lift 33,000 lbs (14,970 kg) 1 ft (0,3 m) in 1 minute.

Horsepower (PS)

The old DIN (Deutsche Industrie Norm) for the power output of an engine. When measuring an engines output the following formula can be used:
1 PS (DIN horsepower) is the power needed to lift 75 kg 1 meter in 1 second (75 mkg/sec.).

Nowadays the Watt (W) is used as a unit of measurement for power.
For conversion the following formulae are used:

1 PS = 0,735499 kW
1 kW = 1,35962 PS

Hot tube ignition

Permanent hot-tube ignition, as developed by Wilhelm Maybach, was formulated as a second patent claim in DRP (Deutsches Reichs-Patent) 28022 of 16 December 1883. With this principle there is an incandescent platinum tube (kept red-hot by a bunsen burner) in the combustion chamber. This method did without the revolutions-inhibiting slide construction, which controlled hot-tube ignition systems had hitherto used. After Otto’s four-stroke patent ran out (on 30 January 1886) this patent of Daimler’s was the cause of many patent infringements and earned Gottlieb Daimler substantial licence fees.

Hot-wire air-mass sensor

The hot wire air-mass sensor is a component of central injection and is used to meter the fuel that is to be injected. This volume is indirectly oriented towards the volume of air drawn in according to the vacuum in the inlet manifold. The hot wire air-mass sensor calculates the volume of air passing the wire, upon which the volume of injected fuel depends, from the current required to keep the wire at a constant temperature.

Hybrid propulsion

Hybrid propulsion is a combination of two different proplusion units. Usually an electric motor is combined with an internal combustion engine. This combination has the advantage of reducing exhaust emissions in built-up areas hat, as electric propulsion can be used at low speeds in town. At higher speeds a selector lever can be used to switch on the combustion engine. The electric motor is used as a generator to charge the battery (like an alternator). The generator is driven by the combustion engine.

Hydraulic brakes

The transmission of brake pedal force is by a hydraulic system to the individual wheels.

Hydraulic brakes / compressed air servo

The transmission of brake pedal forces by hydraulic pressure to the individual wheel slave cylinders of the tractor unit with assistance from a compressed air servo that boosts the pressure on the brake pedal.

Hydraulic brakes with vacuum device (trucks)

Function as with hydraulic brakes, except that pedal force is assisted by vacuum from a brake device that is connected to the inlet manifold.

Hydraulic clutch

With a hydraulic clutch the transmission of force is effected by fluid (usually gear oil). A hydraulic clutch consists of pump wheel, turbine wheel and housing. It is filled with oil, as mentioned.

Function:
The clutch housing is firmly connected to the engine flywheel. One half of the housing is constructed as a pump wheel. The turbine wheel is mounted in the other half on bearings and this half is connected with the gearbox drive shaft. The pump wheel’s blades set the oil in motion. This is forced into the turbine wheel, which then also begins to move.

Hydropneumatic suspension

Hydropneumatic suspension works in a similar way to air suspension. Only here hydraulic fluid is used in addition to air. The pressure of the hydraulic fluid can be raised or lowered by a ride-height control valve (Air = springing element, hydraulic fluid = levelling element).

Hypoid drive

If the engine is installed longitudinally a differential is necessary to turn the power through 90° and transfer it to the wheels via shafts. Differentials are constructed as bevel gears consisting of the bevel drive pinion and the bevel crown wheel. Hypoid drive is usual nowadays: the pinion is not positioned centrally, but is off-set from the middle of the crown wheel. This makes a larger pinion diameter possible and spreads the stresses over a much larger tooth surface area.

Hypoid oil

Hypoid oils are blended gear oils that guarantee perfect lubrication also with high tooth-face pressure, as is the case with differentials using hypoid gears, for example.

I

Ignition coil

The ignition coil transforms the electricity from the battery (usually 12 V, trucks 24 V) into a high voltage.

The ignition coil consists of the primary coil with a few windings of thick wire and the secondary coil with a lot of windings of thin wire around an iron core. When electricity flows through the primary coil a magnetic field is created which cuts the secondary coil, in this way 10,000 to 25,000 volts can be produced, depending on the ratio of windings (1:70-1:100).

Ignition system

Combustion in petrol engine cylinders is initiated by spark ignition. An ignition voltage of approx. 20,000 volts is required to detonate the compressed fuel-air mixture. As a car battery normally has only 12 volts an ignition system is necessary which can transform the voltage of the electricity and then distribute ignition sparks to the individual cylinders according to the firing order. One differentiates between conventional coil ignition systems and coil ignition systems with transistorised control. The conventional coil ignition system consists of ignition coil, contact breaker, capacitor, distributor and spark plugs. The transistorised ignition system, which is being used more and more because of its better efficiency, differs only superficially by the lack of a capacitor and the additionally required ignition switching device.

Ignition timing device

Because of the ignition delay the ignition point must be timed just before TDC (i.e. just before the piston reaches top dead centre).
The higher the engine speed the earlier the ignition point.
With the type of distributor described here advance and retard take place with flyweights and vacuum.

Injection controller

Diesel engine performance is improved if injection is advanced with rising revolutions. This is realised by an automatic centrifugally operating injection injection controller. Its operating range is between 18° and 30° of the crankshaft, according to revolutions.

Injection nozzle

Fuel is sprayed into the cylinder, pre-chamber or swirl chamber through the injection nozzle in aerosol form. The fuel pressure produced by the injection pump lifts the nozzle needle out of its conical seat and opens the way for injection. At the moment when the connection is made to the return pipe by the pump piston helix, pressure falls and the nozzle needle is pressed back into its seat by spring pressure.

Injection pump

The injection pump is a piston pump. It contains a pump element for each engine cylinder consisting of a cylinder and a piston. The piston piston is lifted by a cam and pressed back by a spring.

The piston is fitted so exactly that it seals even at high revolutions and with high pressures. It is lubricated by the remainder of diesel fuel in the pump cylinder. The volume of fuel transported is regulated by a turning of the piston (a push rod in the pump housing turns the control sleeve of the piston via a cogwheel).

Intake manifold injection

Unlike direct injection, whereby fuel is injected directly into the cylinder, with intake manifold injection fuel is injected into the inlet manifold. During the development of the Mercedes-Benz 300SL (W 194/W 198) both systems were experimented with, the final decision for series production was for direct injection.

Integral bodywork

Unlike the long-established chassis construction, with integral bodywork there is no more chassis, but a construction with floor members and wheel arches that bear the load and guarantee the stiffness of the car’s body in combination with the roof, front and rear of the body. The Opel Olympia of 1935 was the first series production car with integral bodywork. Daimler-Benz introduced integral bodywork in connection with the pontoon body with Type 180 (W 120, of 1953). („Pontoon body” as a description of style is not to be confused with the concept of integral bodywork, however. In the USA for example, for many years „pontoon” cars were built with chassis construction.)

K

Knight sleeve-valve engine

In 1909 the Daimler-Motoren-Gesellschaft acquired the licence for the sleeve-valve engine invented by the American Charles J. Knight. The speciality of this engine was the fact that the exchange of gases during combustion did not take place through intake and exhaust valves, but through two pipe-shaped sleeves. Vehicles with Knight engines were produced by the DMG between 1910 and 1924.

Knock

Knock refers to sudden combustion in petrol engines caused by spontaneous ignition. Knocking leads to a sharp rise in pressure and temperature.

Effects on the engine:
Bearings can be damaged by excessive combustion pressure.
Excessive combustion temperature can lead to pistons jamming or seizing.

Causes of knocking:
The use of unsuitable petrol, wrong engine adjustment.

L

Ladder frame (trucks)

A frame with two longitudinal members that are connected by a number of transverse members, either rivetted, welded or bolted.

Leaf spring

A spring consisting of single leaf springs arranged on top of each other. Intrinsic damping occurs from the friction between the single leaves. The axle is controlled by the springs themselves, control arms are not necessary. Leaf springs are mounted on the frame on spring brackets and spring shackles.

Lenoir engine

Jean Joseph Etienne Lenoir (1822-1900) was a versatile inventor. One of the patents that he received was for a gas engine in 1860 with a construction similar to the usual double working steam engines. Lenoir avoided the danger of explosion from pumps, the pistons drew in the gas-air mixture which was ignited when the piston was half-way up the cylinder. Despite the harsh combustion shocks his engine was not as loud as systems with gear racks, as was usual at that time. Lenoir also experimented with a motor car and a motor boat at this early stage.

Low-bed chassis

Low-bed chassis means a construction which is bent over and around the rear axle so that the whole of the vehicle’s body can be lower and thus a low centre of gravity is achieved. Hans Gustav Röhr, design engineer at Daimler-Benz, amongst other companies, built a very early low-bed chassis vehicle. Benz & Co. built a 3-ton truck with a low-bed chassis from 1923.

Low-pressure tyres

In the early years of the automobile, after solid rubber tyres pneumatics were introduced that were pumped up to a pressure of 4 to 8 atmospheres. With better rubber quality and more durable mixtures it became posssible in the middle of the twenties to produce more elastic, wider tyres that were called low pressure tyres or balloon tyres.

M

Master brake cylinder for a dual-circuit brake system

For safety reasons dual-circuit brake systems are fitted to all cars nowadays. They have two independent brake circuits.

The master brake cylinder of this system is constructed as follows:
It has two pistons and two reservoirs instead of one each as with a normal master cylinder. If one brake circuit fails, one of the pistons alone can still supply brake pressure for the remaining circuit.

Master brake cylinder for a single circuit brake system

The master brake cylinder serves to create brake pressure. It is operated from the brake pedal via a rod linkage.

In its simplest form it consists of:

cylinder with compensating bore, bleed nipple and connection for the brake pipe, the piston with filling disc, primary and secondary cup seal and residual pressure valve.

Function:
The piston, which is sealed to the cylinder wall by the primary and secondary cup seals, is pushed forward by the brake pedal and forces the brake fluid through the residual pressure valve into the brake pipes that lead to the wheel slave cylinders.

Maximum axle weight

Maximum load on an axle after consideration of material properties, tyre load factor and legal regulations.

Maximum permitted weight

The maximum weight permitted by the vehicle manufacturer after consideration of legal regulations and material stresses. This weight may not be exceeded (weight empty + load).

Maybach’s float carburettor

Maybach had developed a float carburettor for the „riding car”. By using a float he ensured that petrol stayed at a constant level in the carburettor. In this way a constant fuel-air mixture could be produced. The carburettor was extremely large, its external dimensions were almost as large as the engine. It was also used in the „grandfather clock”, in fact the Daimler-Motoren-Gesellschaft used this carburettor for almost ten years.

Mercedes-Benz diagonal swinging axle

The diagonal swinging axle with starting-torque compensation is a further development of the diagonal swinging axle. By means of special design features this axle prevents a sinking of the rear of the car when driving away or accelerating, unlike conventional diagonal swinging axles.

Mercedes-Benz power assisted steering

With the Mercedes-Benz power assisted steering system the oil pressure that is created by a pump is regulated by a control valve. This control valve is activated by the so-called control ruler on the steering nut. With a rising requirement for strength at the steering wheel the oil pressure necessary for power assistance also rises.

Mid engine concept

Mid engine concept means that the engine is just in front of the rear axle and the rear wheels are driven. This layout is advantageous for the handling and road-holding of a car on a normal road surface, but has disadvantages on a wet surface. The main disadvantage of a mid-engined car is the limited space for passengers.

Mixture lubrication

Mixture lubrication is a method used for the lubrication of two-stroke engines. Oil (so-called upper cylinder lubrican) is mixed with the fuel. In the past special mixing cans were used, this is no longer necessary with modern two-stroke oils. The oil therefore gets into the engine with the fuel and all important parts receive fresk oil with every piston stroke. Another variety of lubrication was the so-called fresh oil lubrication, which was used for a time. With this method oil was kept in a separate tank and was fed to the engine with the fuel by a separate engine-driven pump. However, this procedure proved to be very unreliable.

Muffler

As the exhaust gases flow out of the cylinder into the exhaust manifold and then into the exhaust pipe pressure waves arise which cause a loud noise.

To reduce this noise exhaust mufflers, or silencers, are used, which are constructed according to two main principles:

a) the resonator principle
b) the absorption principle.

O

OHC engine

OHC (overhead camshaft) means an engine construction with the camshaft at the top. The main feature of these engines is the camshaft rotating in the cylinder head, which operates the hanging inlet and outlet valves directly with its cams. This kind of engine is a precondition for high revolutions, it is a feature of almost all modern, high-performance engines.

OHV engine

OHV (overhead valves) is the term for inverte valves in the cylinder head i.e. nowadays in almost all conventional engines valves are installed above the cylinders in a „hanging” position. This construction requires a complex valve operation or a overhead camshaft, but it has the advantage of allowing a more optimal shape of combustion chamber and the inlet ports can be designed better by being straight instead of crooked.

Oil circuit

The engine’s moving parts (crankshaft, con-rods, camshaft, pistons and drive-shafts for fuel pump and distributor) must be lubricated permanently during operation.
A lubrication system is therefore necessary. Wet sump lubrication is the most common type with four-stroke engines. Dry sump lubrication is seldom used.

Oil cooler

As well as lubricating, the oil has to transfer the friction heat away from the bearings. For this reason it becomes very hot. As oil loses its lubricating properties when it gets too hot it has to be cooled while circulating.
This normally occurs by the oil sump giving off heat to the surrounding air
Some engines require an additional oil cooler, usually in the form of an air-oil cooler.

Oil filter

To keep dirt in the engine away from the lubricating points the oil has to be cleaned before it gets to these points. Oil filters are used for this purpose, which are located either in the main flow or the bypass flow of the oil circuit.
With main flow oil filters all of the engine oil is cleaned with every circuit. With bypass flow filters only a part of the oil is cleaned by each circuit, but the filter is finer so that the smallest of impurities can be filtered out. werden.

Oil pump

Gear-type oil pumps are used, driven either by the crankshaft or by the camshaft. Gear pumps are of a simple construction and are reliable.

Otto’s experimental engine

Nikolaus August Otto (1832-1891) had already experimented with an engine that he wanted to make independent of lighting gas in 1861. In this way he stumbled across the effect of compression on combustion. However, he did not succeed with the realisation of his ideas. Otto then turned to the atmospheric principle. In 1863 he managed to combine his engine with a cogged connecting rod and free-wheel clutch. This was his first practical design and he received the Grand Prix for it at the world exposition in Paris in 1867.

Otto’s friend and engineer Eugen Langen (1833-1895) helped him with the production of the engine; in 1872 the Deutz Gas Engine Factory was founded. Gottlieb Daimler joined as technical director with Wilhelm Maybach at his side as chief design engineer. The term „Otto engine” honours Nikolaus Otto as the inventor of the four-stroke engine. However, the patent for the four-stroke principle was declared invalid by the courts and therefore free for general usage. Daimler und Maybach later designed their engines – unlike Karl Benz – according to Otto’s four-stroke principle.

Overdrive

Overdrive (also known as overdrive gear) is an additional gearbox with planetary gears that reduces engine revolutions with a constant road speed. The vehicle’s wheels then turn faster than its engine. The overdrive can be activated mechanically or hydraulically without using the clutch. The practical effect is that of a five-speed gearbox.

Oversteer

Oversteer means that in a bend the steering wheel is turned less than it normally would be. The rear of the vehicle moves out of the bend.

P

Passenger safety cell

The passenger safety provides space for survival in the case of an accident. To guarantee the maximum possible stability a complex system of reinforcements and high-strength connections was developed, which withstands extreme accident stresses. This passenger safety cell does not only reduce the risk of injury from head-on collisions or overturning, but also specifically from side impact and offset frontal collisions. The patent for the concept of the passenger safety cell in combination with the crumple zone was awarded to Béla Barényi in 1951. The first application was at Daimler-Benz in the series W 111 in 1959.

Performance according to DIN

A standard series engine with air filter and exhaust system has to be tested under normal operating conditions, i.e. with standard adjustment of carburettor or fuel injection and ignition timing, with fuel as specified in the operating manual and with the normal temperature of coolant and lubricant.

During the test the fan, water pump, fuel pump and alternator (unloaded) must be driven by the engine. The measurements are given for an air temperature of 20° and a barometric pressure of 770 Hg.

All of the auxilliary units that are considered for the DIN measurement of performance are necessary for the optimal operation of the engine.

Performance according to SAE

This measurement of performance takes place without air filter and exhaust system and without such auxilliary units as cooling fan, water pump, fuel pump and flywheel. To achieve optimal measurements, ignition and carburettor or fuel injection are adjusted to their highest values. Air filter, exhaust system and the auxilliary units take up approx.. 10-15 % of performance, which means that performance according to SAE is higher than that according to DIN by this percentage. Performance figures according to SAE are inappropriate, as in practice no engine runs without these auxilliary units.

Petrol / Gasoline

In official technical language petrol, gasoline, is sometimes referred to as Otto fuel. It is a collective name for various chemical structures of refined crude oil with boiling points from about 25 to 210° Celsius.

At the time of Bertha Benz’s first long distance automobile journey petrol was only sold by pharmacists under the name of „Ligroin”, or naphtha.

The German word for petrol, „Benzin”, has no connection with Karl Benz, but has its root in Arabic.

Petrol injection, elektronic (L-Jetronic)

The L-Jetronic system measures the volume of air drawn in by the engine by means of an air-volume meter and passes this value on to the electronic control unit as a voltage signal. The electronic control unit gives a control impulse to the electro-magnetic injection valves (situated before the engine’s intake valves), which are thus opened for an exactly determined length of time. Injection pressure is held constant by a hydraulic governor. The volume of fuel injected is therefore only dependent on the time that the injection nozzle is open. The electronic control unit carries out the basic function as well as all of the correction functions of the injection system. So if the electronics fail, this injection system cannot supply the engine with fuel at all.

Petrol injection, mechanical (K-Jetronic)

With this petrol injection system the fuel is sprayed into the intake valve of the engine continuously in aerosol form through the injection valve. The quantity of fuel injected is regulated mechanically in connection with the quantity of air drawn in by the engine. The quantity of air drawn in by the engine is measured by an air-volume meter installed just before the throttle valve. A fuel distributor allocates the appropriate volume of fuel required to each cylinder through the injection nozzle.

Petrol injection, semi-electronic (KE-Jetronic)

With this injection system the basic advantages of the tried and tested mechanical system with air volume measurement are complemented by the addition of electronically regulated correction functions. This is achieved by the use of an electro-hydraulic actuator which converts electrical impulses into an alteration of the volume of fuel injected. If the electronics fail, only the correction funcion is interrupted. The basic mechanically controlled injection system is maintained and the engine can continue to operate.

Petrol steam engine

Maybach was interested in the idea of using exhaust heat for additional performance. This idea was also used by the Swiss A. Büchi with his invention of the turbocharger in 1905. Maybach built a combined combustion and steam engine in 1904. The main claim of this patent (of 1902) was: „combined explosive power and steam engine, by which the cooling water is heated by the exhaust gases of the explosive power engine in a special pre-heater, then further heated in a mantel around the explosion cylinder and the pressurised steam that develops is super-heated by the hottest explosion gases in channels of small cross-section, and after the explosion collected in a condenser in a special cylinder and then back to the pre-heater and the mantel of the explosion cylinder”. This was the theory, in practice the combination did not succeed. As soon as the steam engine was switched on engine performance fell from 12.8 to 6.4 horsepower. Operation with methylated spirit did not improve matters, so this is one of Maybach’s developments that went down as a failure in the history of engineering.

Pistol-grip handbrake (trucks)

A pull-brake with a hand-lever situated on the bulkhead or cab floor. The hand-lever is locked by a pawl in the toothed rod.

Pistons

The pistons have to seal the combustion chamber towards the crankcase whilst they are in motion. They have to take the gas pressure that arises during combustion and transfer it via the connecting rods to the crankshaft as a rotation. They also have to conduct the heat given to the top of the piston by combustion quickly to the cylinder walls.

Planetary gear set

A planetary gear set consists of an outer wheel with cogs on the inside, the planetary gears, which are installed in a planet carrier and the sun gear. All of the constituents of the planetary gear set can be used as drive gears or driven gears. To produce a ratio one of the 3 parts must be fixed. In this way the driving gear rolls around the fixed one and creates the ratio to the driven gear.

Planetary rear axle (trucks)

A rear axle with which the required torque is first built up at the wheel hubs by means of a planetary gear set. This means that drive components can be constructed for lower torque.

Pneumatic motor, Maybach

With the pneumatic engine, a design by Wilhelm Maybachs from 1906, the power of a combustion engine was not transmitted to the rear axle as usual via clutch and gearbox, but via a separate compressed air engine. This was a horizontally opposed engine and was operated with a single lever. This lever operated a release valve between the compressed air engine and compressor. If the valve was open, the compressed air was let out and the car slowed down as a result of the internal friction of power transmission. This engine’s efficiency was extremely poor. Only about 1/4 of the engine’s performance actually worked on the rear axle with this method.

Power

Power is work done in a certain time. The unit of power is the watt (previously horsepower). If this is applied to the measurement of engine output the following holds:

power = force x distance (lever arm or radius) / time

P = F x d / t

1 watt = 1 newton x 1 meter / 1 second

or with electricity:

1 watt = 1 volt x 1 ampere

As engines have an output of far more than 1000 watts, the larger unit of kilowatt (kW) is used to quote output. 1 kW is 1000 watts.

Power assisted brakes

As for steering, for the brakes there is also power assistance, which boosts the force of the foot on the brake pedal. With petrol-engined cars vacuum is used from the inlet manifold, which acts on a diaphragm in the brake servo unit. If there is no manifold vacuum available (diesel engines) an additional vacuum pump is required.

Power take off (PTO)

Auxiliary drive with various ratios for different kinds of auxilliary units, which are usually firmly fitted to the vehicle.
The choice of ratio depends mainly on the power requirements of the auxilliary unit. Side power take-offs are fitted to the side of the gearbox housing, power is taken from a gearwheel on the countershaft. Central power take-offs are fitted to the exit end of the gearbox, direct drive with countershaft.

Precombustion chamber method

The pre-chamber method is one of the two most common methods of diesel injection nowadays. With this method the fuel is injected into a pre-chamber that is located in the cylinder head and connected to the main combustion chamber.
The burning of the fuel begins in this pre-chamber. The resulting rise in pressure forces the burning fuel particles into the main combustion chamber where the process of combustion is completed.

Pressure

The bar (b) is the unit of measurement for pressure.

1 bar = 1,02 atmospheres oder 1,02 kp/cm²

Propeller shaft

Cars with engine and gearbox above the driven axle have their gearbox and differential in the same housing.

It is different with cars that have the engine at the front and the driven axle at the rear. With this type of layout the gearbox and the differential are separate.
Power transmission is by propeller shaft, which is connected with universal joints or disc joints.

Propellor shaft brake

The propeller-shaft brake – also called transmission brake – was used from the beginning of this century and partly into the thirties as a driving brake or parking brake (e.g. by Opel). It was in the form of a leather band or belt, which passed over the prop-shaft or the bell-housing of the main shaft of the gearbox. The belt was tensioned with a lever and pressed onto the shaft, which caused deceleration or served as a parking brake. With Daimler-Motoren-Gesellschaft vehicles from the first „Mercedes” up to the Mercedes 28/95 h.p. of 1922 the footbrake operated on the propeller-shaft as a driving brake and the parking brake worked mechanically on the rear wheels.

R

Rack and pinion steering gear

This system consists of a housing in which a gear rack can move up and down and in which a gear wheel that engages in the gear rack can rotate. If the gear wheel starts rotating, the gear rack moves to the left or to the right.

Radial tyres

In radial tyres the cord fibres run parallel to each other, at right angles to the circumference of the tyre and are surrounded by several layers of bracing ply. The bracing plies are between the load bearing carcass and the running surface. A tyre with a radial carcass hardly be able to transmit any transverse forces when rolling. The bracing ply is therefore necessary for exact tracking, it also stabilises the running surface.

Radiator

Only tube-type radiators are used to cool down hot engine coolant nowadays. There is a difference between down-flow and cross-flow radiators. With the first type the radiator tanks are at the top and the bottom; with the second type they are at each side. In both cases the radiator tanks are connected by tubes. Additional ribs are fitted at right angles between the tubes in order to achieve maximum cooling.

Ratchet handbrake (trucks)

Handbrake with ratchet. The effect of the ratchet is that the lever can be pulled repeatedly without releasing the brake and a higher brake shoe pressure can therefore be achieved. The brake is released by operating a pawl.

Rear fin

Enthusiast’s term for the Mercedes-Benz models of the series W110/111/112.

Rear spoiler/wing

A rear wing or spoiler serves to increase the down-force of a vehicle on the road surface. In combination with the air stream it creates negative air pressure, which causes better adhesion of the vehicle and reduces lateral acceleration in bends, which improves fast and exact driving.

Rear wheel drive

Rear wheel drive means that the rear wheels of a vehicle are driven. Rear wheel drive can be combined with front-engine, mid-engine or rear-engine, for example.

Recirculating ball steering

Recirculating ball steering is a special kind of worm-and-nut steering. The steering shaft has an external ball recirculation thread and the steering nut has this type of thread internally. Both threaded parts together make up a ball track. If the steering column shaft is turned the ball-bearings move up or down in this track and take the steering nut with them.

Resonator-type muffler

With the resonator muffler the exhaust gases are thrown back in the direction of the sound’s source by pieces of sheet metal. The sound is then reduced by the friction of the gases flowing in the opposite direction.

Retarder (trucks)

A retarder is an additional system to relieve or complement the braking system. An electro-magnetic retarder consists of two main parts. The stator, which is fitted to the vehicle’s frame and contains electro-magnetic induction coils, which create a magnetic field; the rotor, consisitng of two ribbed soft-steel discs, which rotate in the magnetic field and are driven by the axle or cardan shaft.

Rigid axle

With rigid axles both wheels are connected to each other rigidly and are suspended from the vehicle’s body together. If a rigid axle is driven, the axle housing is often also used as diffential housing and casing for the drive shafts. This type of axle has a high unsprung mass, which can have negative effects on handling.

Rim designation Rim designation

Wheel rim designations include the following details:

(example): 6J x 14 H 2

6 = rim width in inches
J = identification letter for the height and contour of the flange
x = identification letter for a single piece drop-centre rim
14 = rim diameter in inches
H2 = rim cross-section on the outside and inside with humped rim

Roots compressor (rotary piston compressor)

The Roots compressor, also called rotary piston compressor, works in a similar way to a gear wheel pump. The rotating parts, they can have two blades or three, roll around each other and transport the gas-flow by means of their contra-rotations. Rotary piston compressors do not compress by reducing the size of a pump chamber, it is rather that compression is due to delivery pressure.

Rotary engine

The rotary engine (also called Wankel engine after its inventor) has one or more triangular pistons with curved sides instead of several reciprocating cylinders. The cylinder perfoms a circular movement in a housing with a shape like an oval with a narrower middle section. This gives rise to the formation of three chambers whose shapes change with the movement of the piston. The power cycles of the four-stroke engine take place in these chambers. However, the exchange of gases takes place through ports in the housing which are alternately opened and covered by the rotary piston.

S

Shock absorber

Vibration dampers – commonly called shock absorbers – have the function of making oscillations of a vehicles body on its springs subside quickly. They also have to prevent the vehicle’s wheels from leaving the ground.

As a rule nowadays cars use telescopic fluid-filled shock absorbers in single-tube or twin-tube construction. Both designs work on the principle of a piston fitted with valves moving up and down in a fluid-filled cylinder, whereby the flow resistance of the fluid has to be overcome. With twin-tube construction the fluid that is displaced by the piston rod is forced through a valve in the base of the cylinder into a second tube that surrounds the first. With the single-tube system the changing volume is compensated for by a cushion of gas inside the tube (with or without separating piston).

Side-valve engine

Side valves is the expression for a design of cylinder head whereby the valves stand at the side of the engine. They are usually operated by push rods. This type of engine is no longer usual as it only allows low revolutions and low power output per liter. The last Mercedes-Benz with a side-valve engine was the Type 170V.

Single-circuit brake system

Front and rear wheels are braked via a single brake circuit.
If a brake line is damaged, the operating brake fails.

Single-joint swinging axle

The principle of the single-joint swinging axle goes back to a patent by Edmund Rumpler from 1903. However, he did not realise this axle construction until 1921 in his drop-shaped car. Daimler-Benz used this principle for the first time in the Type 170 (W 15), but as a double-joint swinging axle. Not until after the war was the single-joint swinging axle used again in an improved form in the Type 220a (W 180 I, 1954 – 1956). Significant improvements in road-holding, handling and safety were be achieved by the standard use of a single-joint swinging axle controlled by longitudinal arms. This axle was suspended centrally, providing an elastic connection between differential and chassis floor, was resilient to transverse forces and was supported at the sides.

Single-line trailer brake (trucks)

Only one brake line coupling is required with this type of brake system. This line is used to transfer compressed air to fill the trailer’s reservoir and also to activate the brakes (reservoir and control line). While the brakes are being operated the transfer of compressed air to the reservoir is interrupted.

Single-pivot steering

Single-pivot steering is the type of steering that was common originally on carriages. The front axle turns on a single pivot fitted to the middle of the vehicle. Gottlieb Daimler used this form of steering on his motor carriage (1886).

Sleeve-valve engine, Knight’s principle

The speciality of the Knight engine is that the exchange of combustion gases is not controlled by inlet and outlet valves, but by two pipe-shaped sleeves, which move between cylinder and piston and have inlet and outlet ports. The Knight engine was used by the Daimler-Motoren-Gesellschaft in the Mercedes-Knight from 1909 to 1924.

Spark plugs

The spark plugs’ job is to ignite the fuel-air mixture in the cylinder by means of a spark that jumps from one electrode of the spark plug to the other. The central electrode is insulated from the body of the spark plug. High demands are placed upon this insulation as well as on the electrodes by working pressure of 40 bar and combustion temperatures of approx. 2000° C.

Split axle (trucks)

The load-bearing part, a double-T forged member, keeps all stresses away from the power train. Full torque is first built up at the side spur gear drives. This means that the differential can be smaller and therefore more ground clearance can be achieved.

Spring-loaded cylinder (trucks)

In a cylinder a spring is pre-tensioned by compressed air. When the brakes are operated a valve is activated, releasing air from the cylinder. The spring now presses on a lever which in turn presses the brake shoes against the brake drum.

Springing

Springs are installed between the wheel or the wheel suspension and the wheel arch. The springs are meant to absorb shocks from the road surface and to guarantee permanent road contact of all four wheels.
The following types of spring exist:
leaf springs, coil springs, torsion-bar springs, air springs, hydro-pneumatic springs.

Starter motor

The starter motor is an electrical motor powered by the battery that turns the flywheel – and thus the crankshaft – by means of a pinion gear. Due to the high revolutions of the starter and the high gear ratio of the starter gear-wheel to the flywheel both the torque and the revolutions required to start the engine can be provided.

Starter motor (trucks)

This is a main current motor powered by the battery, which engages a cogwheel in the engine flywheel when starting.
The required torque is made possible by the high ratio between cogwheel and flywheel ring gear.

Starting pilot (trucks)

Starting aid for diesel engines. With this device, which is usually used with direct injection engines, a fuel that evaporates particularly quickly is mixed with the intake air while starting. Due to the ignition performance of this mixture it is possible to start the engine even at very low ambient temperatures.

Steering

The steering consists of steering wheel, steering shaft, steering box and track rods, which provide the connection between the steering box and the two front wheels.

Steering box

The rotations of the steering wheel are stepped down in the steering box and transmitted to the front wheels via the track-rods.

Steering offset

Camber angle and – spread angle hit the road at certain points. The distance between these points is the steering offset, or king-pin offset. If the imaginary intersection of the extended axes of rotation is outside the wheels point of contact (seen from the front or from the rear), steering offset is negative.

If it is inside, steering offset is positive. If both points hit the road surface together, steering offset is zero.

Steering servo

Steering boxes can be equipped with steering assistance. This steering servo works, in principle, as follows: a hydraulic control unit activates valves, which guide hydraulic fluid that is pressurised by a pump to pistons, which are connected to the steering roller or steering sector. According to the movement of the steering wheel the fluid exerts pressure on the left of the piston or the right and assists steering in this way.

Steering stub axle (trucks)

Front axle with a forged axle centre casing at the ends of which the steering stub axles are bolted.

Steering-axis inclination

The axes of rotation of the steering axle stub and of the suspension strut are fitted with a certain inclination to the inside (nearer to the vehicle’s longitudinal axis at the top than at the bottom). This incination is called steering axle inclination, king-pin inclination or set.

Steering-axis inclination (trucks)

Inclination of the axis of the steering-swivel pin (kingpin) to a vertical line through the road surface (vehicle loaded up to maximum total weight).

Step carburettor

The exterior of the step carburettor resembles the twin carburettor. However, its internal construction is quite different, as is its function.
Whereas the twin carburettor has an intake pipe from each mixing chamber, the step carburettor has a single intake pipe from both mixing chambers that supplies all cylinders.
Another difference is the fact that the throttle valves of the two mixing chambers open one after the other: up to approx. half the maximum engine speed only the throttle valve of the first mixing chamber is open. The throttle valve of the second chamber is opened automatically by a vacuum or by a rod when the engine needs more fuel at higher revolutions.

Stepped piston

The stepped piston – one of Wilhelm Maybachs inventions – was used in the grandfather clock. In principle this engine already worked with a form of pre-compression. Similar to a two-stroke engine, the fuel-air mixture was drawn in beneath the piston by its upward movement and then let into the combustion chamber through the piston valve as the piston moved down. The crankcase was used as a scavenge pump and a feed pump and therefore had to be a sealed unit. However, this concept had one serious design weakness: the valve coked up very quickly, which caused compression losses. Maybach had been inspired to this design by a patent for a two-stroke engine of 1878.

Stroke

Stroke is the distance travelled by the piston in the cylinder between top dead centre and bottom dead centre.

Super-Single-Tyres (trucks)

Tubeless tyres of a conventional construction with a wide contact area. Replaces twin tyres as a single tyre with appropriate dimensions; also available as a radial tyre.

Surface carburettor

The surface carburettor was a simple pan made of sheet-metal containing petrol. Air was drawn in over the petrol. However, this achieved an insufficient mixture of fuel and air and moreover, materials that did not easily evaporate were dposited at the bottom of the pan. The surface caburettor was also very dependent on the ambient temperature.

Swirl chamber method

With this method air flows into the swirl chamber during compression through a duct that leads into the swirl chamber at a tangent. An air swirl results, which is advantageous for an efficient mixture of air and injected fuel. The combustion process is therefore started in this sphere-shaped or disc-shaped chamber taht is located in the cylinder head. The following sequence is much the same as with pre-chamber combustion.

Synchromesh

With synchromesh gearboxes all gear-wheels are engaged, i.e. rotating while the gearbox is being used. However, due to varying ratios they have different rotating speeds from the main shaft on which the selector sleeve is situated. To make shifting possible the gear-wheel to be selected must therefore be decelerated or accelerated so that it runs at the same speed as the selector sleeve. The synchromesh mechanism performs this task. It works on the same principle as a friction clutch, which is fitted either with inner or outer bevels.

T

Tandem rear axle (trucks)

Second rear axle, installed either as a drive axle (Mercedes-Benz designation: 6×4) or as a trailing axle (6×2).

Telescopic steering column

The safety steering system serves to prevent severe injury to the driver resulting from a frontal collission. The telescopic steering column prevents the steering column from being pushed back into the passenger compartment. The outer tube is in two parts; the steering spindle can in fact be pushed together twice as far as this, as it reaches further forward to the steering box.

Thermostat

The thermostat monitors the temperature of the coolant. If the temperature is below 80° it stays closed. The water circulates only within the engine block and through the heat-exchanger of the heating system if this is in use. With higher temperatures the thermostat opens and lets the coolant flow through the radiator.

Three-stage springs (trucks)

Three-stage springs consist of a main spring, which is used alone when the truck is unloaded. Under a light load the supporting springs, situated under the main springs, begin to work. With higher loads up to full load the additional springs also come into use so that the full springing performance is available.

Toe-in

To improve a vehicle’s straight line behaviour the basic alignment of the front wheels is done with a slight inclination to the inside (seen in the direction of travel). This adjustment is called toe-in.

Torque

For torque (T) a force is required (F). – With an engine this is the effective piston force, which depends on piston area and average working pressure. – The second factor is a lever arm (l) or a radius (r), where this is the distance from the centre of rotation to the point where the force acts.

In the case of an engine this is the distance between the centre of the crankshaft and the centre of the connecting-rod bearing. This gives the formula:

torque = force x lever arm or radius
(T) = (F) x (I) or (r)
1 Newtonmeter = 1 Newton x 1 metre

Torque converter

The torque converter differs from the hydraulic clutch in that it has a stator between pump wheel and turbine.

Function:

As with a hydraulic clutch the pumpwheel is driven by the engine and drives the turbine, which is connected to the drive-shaft, by means of a power transmission medium (oil). When the oil flows back from the turbine to the pump wheel it is diverted by the blades of the reactor. In this way a larger or smaller „lever effect” is achieved, depending on flow strength, which converts the torque into approximately double (according to design) as a result of the large difference in revolutions between pump wheel and turbine.

Torsion bar

With torsion bars a spring rod is turned by a lever which is acted upon by movements of the axle or of a wheel. They need no special care or maintenance.

Total capacity

Total capacity is the capacity of all of an engines cylinders expressen in cubic centimetres

Formula: r² x pi x s x number of cylinders

Touch and spark ignition

Actually an older expression for magneto ignition, with which automobiles were equipped until the thirties. The high tension magneto, invented by Robert Bosch in 1902, is a dynamo for generating alternating current (alternator). Its main components are magnet, anchor, contact breaker and distributor. The electricity produced in the primary winding is interrupted every half revolution whereby the magnetic field „jumps” and transmits high tension electricity to the secondary winding, which is also on the anchor. This electricity then produces a sprk at the spark plug.

With low tension ignition, which was common until the 1910s, a contact breaker mechanism projects into the combustion chamber of the cylinder. The electricity is „broken off” with the rotation of the anchor, which is why this type of ignition is also known as „make and break ignition”. Magneto ignition is dependent on an external source of electricity (battery) and was the forerunner of battery ignition. i

Track

The distance between the two wheels of the same axle (measured at the point of contact of the tyre with the road from tyre centre to tyre centre).

Track (trucks)

The distance between the two wheels of an axle measured on the ground; with single tyres the distance from tyre centre to tyre centre, with twin tyres the distance between the centres of the two twin tyres.

Track circle (trucks)

Diameter of the circle performed by the centre of the outer tyre with maximum turn of the steering wheel on the road surface.

Trailing arm

Trailing arms are links fitted longitudinally to the vehicle and used as single links for controlling rigid or swinging axles.
As double trailing arms (two trailing arms or trailing links fitted above each other) they are used to control steered front wheels. With this construction there are no changes in track or camber when the wheels move due to spring travel.

Transfer box with torque distributor

Transfer box on all-wheel drive vehicles with permanent drive to front and rear axle whereby engine output is divided approximately according to axle load (1/3 front, 2/3 rear). Any drive tension flows off via a lockable interaxle differential.

Transistor ignition system

With a transistor ignition system the build-up and collapse of the magnetic field is controlled by transistors installed in an ignition control unit. Only the controlling current for the transistors flows through the contact-breaker. This is 20 to 30 times smaller than the primary coil’s working current, which means that the contact-breaker points are not subject to as much wear and tear and no capacitor is necessary.

Transmission: 4-matic

The 4-MATIC was first used in Mercedes-Benz models of the series W/S124. It is a form of disengageable all-wheel drive that is regulated by an electronic control unit. Four-wheel drive an the two differential locks are only engaged when required by road conditions. When all-wheel drive is engaged, power is distributed 35% to the front axle and 65% to the rear. It is always engaged if traction or gradient make it necessary. The driver is informed that the system is activated by a display in the dashboard. This also gives him important information about road surface conditions.

Transverse control arm (wishbone)

Transverse control arms (wishbones) are installed at right angles to the vehicle’s longitudinal axis. They are used singly or in pairs in connection with suspension struts or damper struts to control the movements of independently suspended wheels.

Trembler coil ignition

Lenoir’s first gas engine alreay had electrical high tension trembler ignition. The inventor states in his patent specification of 1860 that a Ruhmkorff spark indicator is used for the ignition current, which is supplied by a galvanic element or another source of electricity. Two platinum wires with porcelain insulation are used as electrodes for sparking in the cylinder.

With Benz’s trembler ignition of 1885 the secondary winding was alternately opened and closed by an non-circular disc which was fitted to the camshaft rotating at half of engine revolutions. A lever with a roller ran on the disc. There was a contact on the roller with a drilled hole in which the wire of the secondary winding was fixed. A small leaf spring was fitted to this contact. When the roller passed over the cut-out part of the disc the spring no longer touched another earthed spring opposite and the secondary current flowed to the spark plug where a spark was produced. But when the rest of the disc pressed the springs together, the secondary current was short-circuited and the sparking stopped.

Tube-type radiator

In 1897, with the tube-type radiator, Maybach managed to solve the problems that had existed until then with the cooling of vehicle engines. With this type of radiator cooling water passed through a number of tubes that were gathered together in a rectangular container. With the addition of a fan, cooling was also possible when the vehicle was standing. This new cooling method also made it possible for engine output to be increased from 4 to 10 h.p. The tube-type radiator was not patented, but was a registered design (No. 107 418).

Turbine

The turbine is a power engine by which the flow energy provided by steam or combustion gases works on one or more blades of a drive shaft. With a gas turbine combustion gas is produced by the burning of liquid fuel in a combustion chamber. This gas flows through an exhaust port at the end of the combustion chamber onto a turbine wheel, thus driving it. The torque produced in this way is transferred to the gearbox by a drive shaft.

Turning clearance circle

Diameter of the circle performed above the road surface by the outermost part of the vehicle with maximum turn of the steeering wheel.

Twin-choke carburettor

With the twin-choke carburettor two carburettors are included in one housing. The twin carburettor has two mixing chambers and two jets, but only one float and accelerator jet.
This sort of carburettor is mainly used on high performance engines as in this case one carburettor has to supply fewer cylinders than with a single carburettor and in this way the rate of filling and the mix-ratio in the individual cylinders is more homogeneous.

Two-stage flyweight governor (trucks)

A device that governs the idling speed and the maximum permitted revolutions of an engine. The governor is usually flanged onto the injection pump. Two flyweights driven by the injection pump camshaft work consecutively on two pairs of springs: the idling springs and the end springs.
With a control lever the flyweights contact the regulating rod of the injection pump and move it. The governor does not work in the range between idling speed and maximum revolutions.
In this range the regulating rod is moved by the lever from the accelerator pedal.

Tyre designation (cars)

Car tyre designation according to ECE guidelines include the following details:

– the nominal width of the tyre in mm
– the cross-sectional ratio of the tyre e.g. 70 = the height of the cross-section of the tyre amounts to 70% of its width (if this figure is not given, then the ratio is 80% )
– the type of tyre construction e.g. „R” for radial or belted tyre
– the appropriate wheel rim diameter for the tyre – given in
inches – e.g. 14 = 14 inch wheel rim.
– the load index figure for the tyre e.g. 90 denotes a load bearing capacity of 600 kg
– the letter for the maximum speed of the tyre
Q = winter tyres up to 160 kph maximum speed.
S = tyres up to 180 kph maximum speed.
H = tyres up to 210 kph maximum speed.
V = tyres up to 210 kph maximum speed.

(With tyres for maximum speeds above 210 kph no load index figure is given and the maximum speed letter is given before the letter for the type of construction.)

Examples of tyre designation:

175 R 14 88 S = radial tyre 175 mm nominal width
height:width = 80% wheel rim 14 „
load factor 88 maximum speed 180 kph

195/70 R 14 89 H = radial tyre 195 mm wide
height:width = 70% wheel rim 14″
load factor 89 maximum speed 210 kph

205/70 VR 14 = radial tyre 205 mm wide
height:width = 70% wheel rim 14″
maximum speed over 210 kph

Other details given on the tyre are:

tube type = tyre with inner tube
tubeless = tyre without inner tube
M + S = mud and snow tyre
and the detail beginning with DOT indicates the date of manufacture of the tyre:
e.g. 019 = manufactured in January 1979.

Tyre designation (trucks)

Tyre designation basically consists of two numbers separated by a dash or a letter of the alphabet. The first number is the approximate width of the tyre, the second gives the diameter of the appropriate wheel rim in inches. Belted tyres with a radial carcass for trucks are designated with the letter R.

Tyre load rating (trucks)

Tyre load rating is determined by the air pressure in the tyre. However, permitted maximum pressure depends on the strength of the tyre’s carcass. The ply rating number (PR No.) after the size number gives an indication of carcass stability and maximum load rating.

Tyres

Tyres consist of the load bearing carcass, the running surface with tread and the the tyre beads with steel wire cores, which prevent radial expansion on the wheel rim and ensure a firm fit.
The following types are possible:
Normal tyres (cross ply) und belted tyres (radial ply) mit textile, steel or glass fibre reinforcement. Both types exist with or without inner tube. Nowaday nearly all cars use tubeless radial tyres.

Tyres, tubeless

The main feature of the tubeless tyre is: air-tight rubber layer on the inside and tyre bead sealing between the foot of the tyre and the wheel rim.

U

Understeer

Understeer means that the steering wheel is turned more than it normlly would be. The front of the car moves out of the bend.

Unit

In order to achieve international harmony in the quoting of technical specifications, legal units are valid, the basic units of which are those of the internationally used unit system. The following units are amongst the most important for the automotive industry:

Force (F)
The unit of measurement for force is the newton (previously kp, kgf, lbf were used).

Work (W)
The unit of measurement for work is generally the Joule (previously mkp, PSh were used).

For any work a force (F) must act over a distance (d). This gives the following formula:

Work = Force x Distance
(W) = (F) x (d)
1 Joule = 1 N x 1 m

Unladen weight (trucks)

Weight of the vehicle when ready for use, i.e. the weight of chassis and running gear plus the weight of the complete body and the weight of all equipment normally carried such as spare wheel, trailer coupling, tools, jack. 70 oder 75 kg are also added for the driver.

When checking the weight afterwards of chassis and running gear ready for use or unladen weight, a deviation of +/- 5% is permitted.

V

Vacuum governor (trucks)

In the inlet manifold there are different levels of vacuum at different revolutions. These are transferred by a pipe to a spring-loaded diaphragm, which is connected to the control rod.
The strength of the vacuum determines the position of the diaphragm and therefore also of the control rod. Idling speed and maximum revolutions are adjusted by screws, which serve as stops for the throttle valve situated in the inlet manifold and operated by the accelerator pedal linkage.

Vacuum ignition advance device

The vacuum device advances the timing with the help of negative pressure from the inlet manifold. This vacuum acts on a diaphragm which is connected to the contact-breaker plate in the distributor by a pull rod. With rising pressure the diaphragm is moved so that the contact-breaker plate turns in the opposite direction to the rotation of the distributor and therefore advances the ignition timing.

Valves and camshaft

With four-stroke engines (whether petrol or diesel) inlet and outlet valves are required to control the exchange of gases. One or more camshafts are also necessary to open and close the valves at the correct time.

Variable speed gearbox (Wilhelm Maybach)

A variable speed gearbox with cogwheels was used for the first time by Wilhelm Maybach in his „car with wire-spoked wheels” (1889). It had four gears, which were selected by two levers and had pairs of straight toothed cogwheels. There was no gearbox housing, the whole of the mechanics was freely accessible.

Variable speed gearbox, syncromesh

The synchromesh variable speed gearbox consists of gearbox housing, drive shaft, main shaft, intermediate shaft, the gearwheels (a pair for each gear, except the direct gear), synchromesh parts, the selector fork, the selector sleeves and the externally fitted gear lever.

Function:
With a synchromesh gearbox all pairs of gearwheels are engaged. The gearwheels on the intermediate shaft are firmly connected with it, whereas the opposing gearwheels on the main shaft are on free bearings.
Only when a selector sleeve is pushed against one of the gearwheels by the selector fork is a connection between a gearwheel and the main shaft created. A gear is now engaged.

Vehicle height

Maximum height of a vehicle (measured unloaded with recommended tyre pressure).

Vehicle length

Maximum length of a vehicle (measured including the bumper bars).

Vehicle width

Maximum width of a vehicle (including door handles, fittings or other similarly projecting parts, but excluding mirrors).

Vertical drive shaft

The vertical drive shaft is driven by the crankshaft and in turn drives the camshaft. This technique was used predominantly in the twenties.

Daimler had already supplied a 300 horsepower six-cylinder engine with vertical drive shaft, on which the well-known design engineer Boris Loutzky had cooperated, in 1902.

Daimler-Motoren-Gesellschaft’s Grand Prix racing car of 1914 was fitted with a vertical drive shaft developed by Paul Daimler in 1913, which was also used in the Mercedes Type 28/95 (1914-1915 and 1920-1924). A vertical drive shaft was also used in the first Mercedes compressor car, Type 6/25/40 h.p. (1921-1925).

Viscous fan coupling

Fan operation, which switches on or off automatically according to coolant temperature. Two crossed bi-metal strips are used as temperature sensors. Their expansion movements operate a valve mechanism, the fluid of which (silicon oil) produces power transmission. When the fan is switched off up to 8 h.p. can be saved.

W

Weight to power ratio

The weight to power ratio of a vehicle used to be quoted in kg/h.p. As output is given in kilowatts nowadays, the weight to power is also given similarly as:

kilogram/kilowatt (kg/kW).

Thus a vehicle with a weight of 1000 kg wiegt and engine output of 100 kW has a weight to power ratio of:
1000 kg / 100 kW = 10 kg/kW.

Wet sump lubrication

Wet sump lubrication is a special type of pressure lubrication.
With few exceptions, wet sump lubrication is the state of the art nowadays. With this type of lubrication most of the oil is contained in an oil sump below the crank-case.
The oil is drawn up by a pump and forced to the points of lubrication in the engine from where it flows back into the sump by gravity.

Wheel brake cylinder

With drum-brakes the pressure created in the master cylinder is passed on to the wheel brake cylinders and then on to the brake pads via the brake pistons. Wheel brake cylinders consist of a cylinder, one or two pistons with sealing rings and a spring, which keeps both pistons in contact with the brake linings.

Wheel rims (cars)

With cars one differentiates between pressed steel disc wheels and forged or cast light alloy wheels.

Pressed steel dics wheels:
With this type of wheel the wheel centre member is pressed out of sheet metal and welded to the rim well.

Light alloy wheels:
The use of this type of wheel means that the weight of unsprung components is reduced. The wheel centre member and the rim well are integrated in a single unit. They are either cast or forged.

Hump-shoulder rim:
The hump-shoulder rim has depressions at both sides that accept the tyre bead. The tyre sits particularly well in these depressions, which also prevent the tyre bead from being pressed from the rim flange when driving in a bend.

Drop centre rim:
The name of this type of rim describes its cross section.
Both steel rims and light alloy rims on cars are drop centre rims. The name comes from the depression in the rim well which is necessary so that the tyre can be fitted.

Wheel rims (trucks)

The rim is the part of the wheel where the tyre is fitted. The wheel consists of rim and wheel disc or wheel centre member in the case of Trilex-wheels.

The following types of wheel cross-section exist:
– tapered rim
– tapered rim for tubeless tyres
– Trilex-rim (sectionally divided tapered rim) with bolted on wheel centre member.

In the rim designation the first figure refers to the rim width (flange to flange) in millimetres and the last figure gives the diameter of the rim in inches.

Wheel springing, wheel control

1) Springing (Coil springs)
2) Shock absorbers
3) Stabilizers
4) Wheel suspension front wishbone rear semi-trailing arm
5) Drive shaft

Wheel suspension

Wheel suspension is responsible for the controlled movement of the axles and therefore the wheels. Different control arms are used as components of wheel suspension: longitudinal (trailing arms), transverse (wishbones) and diagonal (semi-trailing arms).

Wheelbase

Distance between front axle and rear axle (measured from the centre of the front axle to the centre of the rear axle).

Wood carburettor

Due to the increasing shortage of petrol during World War II a so-called wood-gas apparatus was ccompulsory for civilians’ vehicles, commonly called a „wood carburettor”. Carbon dixide and methane were first produced in a generator by burning hardwood. By adding air a combustible gas mixture was produced, which was fed into the engine. This was a troublesome process for everyday use, as one had to begin burning approx. one hour before the journey and maintenance work had to be carried out during the journey, apart from the unpleasant smell and soot. In addition, it was necessary to carry a stock of wood and to clean the fuel container at the end of each journey.

Worm and nut steering gear

Worm and nut steering has a steering screw and steering nut. If the steering wheel is turned to the left or to the right the steering nut moves up or down on the steering screw. These up and down movements are transmitted to the steering shaft by sliding blocks and a fork lever.

Worm and roller steering gear

Instead of a steering sector this system has a steering roller. The worm gets narrower towards the middle in a circular form. When the worm is turned the roller moves up or down a circular line and in this way goes through a swinging motion.

Worm and sector steering gear

This system is based on worm and steering sector. If the worm is set in motion by the steering wheel being turned, the sector turns on the worm and takes the steering gear arm with it.

Worm gear steering

Worm gear steering can be equipped with a steering segment, a steering roller or a steering finger. The main difference is between worm and sector steering and worm and roller steering.