{"id":2556,"date":"2023-11-13T23:04:43","date_gmt":"2023-11-13T22:04:43","guid":{"rendered":"https:\/\/mbci.mackuz.ovh\/?p=2556"},"modified":"2023-11-13T23:04:43","modified_gmt":"2023-11-13T22:04:43","slug":"removal-and-installation-of-carburetor-cover","status":"publish","type":"post","link":"https:\/\/mbci.mackuz.ovh\/index.php\/2023\/11\/13\/removal-and-installation-of-carburetor-cover\/","title":{"rendered":"Removal and installation of carburetor cover"},"content":{"rendered":"

 <\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
07.2\u2014192 Removal and installation of carburetor cover<\/strong><\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Tightening torques<\/strong><\/div>\n<\/div>\n<\/td>\n
\n
\n
Nm<\/div>\n<\/div>\n<\/td>\n
\n
\n
(kpm)<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
with new insulating flange<\/div>\n<\/div>\n<\/td>\n
\n
\n
10<\/strong><\/div>\n<\/div>\n<\/td>\n
\n
\n
(1.0)<\/strong><\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Carburetor fastening nuts<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
with insulating flange used up to now<\/div>\n<\/div>\n<\/td>\n
\n
\n
8<\/div>\n<\/div>\n<\/td>\n
\n
\n
(0.8)<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Special tool<\/strong><\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Torque wrench 4\u201416 Nm (40\u2014160 kpcm)<\/div>\n<\/div>\n<\/td>\n
\n
\"m110<\/div>\n<\/td>\n
\n
\n
000 589 67 21 00<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Removal<\/div>\n<\/div>\n<\/td>\n
\n
\"m110<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
1 Remove air filter.<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
2 Pull off fuse (43) and disconnect choke rod.<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
3 Unscrew carburetor fastening nuts.<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
4 Unscrew carburetor cover fastening screws (arrow).<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
5 Force off carburetor cover at forcing-off point and remove.<\/div>\n<\/div>\n<\/td>\n
\n
\"m110<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
07.2.2 la\u2014192\/1<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

 <\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n
<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Installation<\/strong><\/div>\n<\/div>\n<\/td>\n
\n
\"m110<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
6 Install carburetor cover in vice versa sequence. Use new gasket.<\/div>\n
Attention!<\/strong><\/div>\n
Prior to mounting carburetor cover, make sure that holddown (34) is installed.<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
Tighten carburetor fastening nuts uniformly and crosswise to specified torque.<\/div>\n
Attention!<\/strong><\/div>\n
To prevent distortion of carburetor, tighten with a torque wrench only and up to specified torque.<\/div>\n<\/div>\n<\/td>\n
\n
\"m110<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n\n
\n
07.2.2 la-192\/2<\/div>\n<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n
<\/td>\n\n
\n
<\/div>\n<\/div>\n

 <\/td>\n

<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/td>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

 <\/p>\n

 <\/p>\n

 <\/p>\n

 <\/p>\n","protected":false},"excerpt":{"rendered":"

    07.2\u2014192 Removal and installation of carburetor cover   Tightening torques Nm (kpm)   with new insulating flange 10 (1.0)   Carburetor fastening nuts   with insulating flange used up to now 8 (0.8)   Special tool   Torque wrench 4\u201416 Nm (40\u2014160 kpcm) 000 589 67 21 00   Removal 1 Remove air filter. 2 Pull off fuse (43) and disconnect choke rod. 3 Unscrew carburetor fastening nuts. 4 Unscrew carburetor cover fastening screws (arrow).   5 Force off carburetor cover at forcing-off point and remove.   07.2.2 la\u2014192\/1       Installation 6 Install carburetor cover in vice versa sequence. Use new gasket. Attention! Prior to mounting carburetor cover, make sure that holddown (34) is installed.   Tighten carburetor fastening nuts uniformly and crosswise to specified torque. Attention! To prevent distortion of carburetor, tighten with a torque wrench only and up to specified torque.   07.2.2 la-192\/2          <\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[32,27],"tags":[],"class_list":["post-2556","post","type-post","status-publish","format-standard","hentry","category-carburetor-fuel-pump-throttle-linkage","category-m110"],"aioseo_notices":[],"aioseo_head":"\n\t\t\n\t\n\t\n\t\n\t\n\t\n\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t\n\t\t